manualshive.com logo in svg

Symmetricom TimeProvider 500 series, Справочное руководство

Поделиться
Скачать
Symmetricom TimeProvider 500 series Скачать руководство пользователя страница 136

TMSL 097-44018-26

Issue 2: Sep 99

Page 136

COMMAND CODE: SET-ATTR-CONT

PURPOSE

SET ATTRIBUTE CONTROL

This command sets the control preferences.

1.

Input protection type (DCIM only) (aid = DCIM-ALL):

a. No protection: each DCIM card functions as a stand-alone card with 2 inputs
b. 1-plus-1 (1+1) protection: the 2 DCIM cards function as 1 input card with 4 inputs

2.

SSM Mode (applies to a single shelf or GTI card) (aid = MIS or GTI-1 or GTI-2):

a. SSM is not supported
b. SSMT: SSM is supported for DCIM-T, TOTA-M, and GTI-17 cards only
c. SSME: SSM is supported for DCIM-E, EA10-M, EA20-M, and GTI-18 cards only
d. SSMEC: same as SSME plus one additional quality level: QL-UNK

3.

Output source selection mode (applies to master and all expansion shelves) (aid = SHELF):

This option sets the timing output source selection mode (revertive or nonrevertive) which deter-
mines how the timing output cards select which internal synchronization source to use. This applies
to the four sources in the pairs shown below.

Revertive mode: The highest available source is always used.

1st choice:

clock card 1

2nd choice:

clock card 2

3rd choice:

input card 1

4th choice:

input card 2

•

If any of the above sources fail, the next available source is used.

•

If a higher source is fixed, the system uses that higher source.

Nonrevertive mode: Within the pairs shown below, sources are nonrevertive; between pairs, sources
are revertive.

1st pair

2nd pair

clock card 1

input card 1

clock card 2

input card 2

•

If clock card 1 fails, clock card 2 will be used.

•

If clock card 1 is fixed, clock card 2 continues to be used (nonrevertive).

•

If both clock cards fail, input card 1 is used.

•

If input card 1 fails, input card 2 is used.

•

If input card 1 is fixed, input card 2 continues to be used (nonrevertive).

•

If either of the input cards are being used and any clock card is fixed, that clock card will
be used.

4.

Output protection type (TO-EA5, EA10, EA10M, EA20, & EA20M only) (aid = TO-a):

a. No protection
b. 1-for-1 (1-1) protection: one timing output card in an even-numbered slot is a standby for one tim-

ing output card of the same type in an odd-numbered slot (outputs of standby timing output card
are off until working card fails)

c. 1-plus-1 (1+1) protection: one timing output card in an even-numbered slot is a hot standby for

one timing output card of the same type in an odd-numbered slot (the outputs of both cards are
always active)

Содержание TimeProvider 500 series






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды