manualshive.com logo in svg

Symbol SE 923, Руководство по интеграции

Поделиться
Скачать
Symbol SE 923 Скачать руководство пользователя страница 186

6-30

SE-923 Scan Engine Integration Guide

SCAN_ENABLE

Description: Permit the decoder to scan bar codes

Packet Format

Field Descriptions

Host Requirements

The host sends the SCAN_ENABLE command to tell the decoder to allow scanning. Scanning 
is enabled upon power-up, so this command need only be send if a prior SCAN_DISABLE 
command has been sent.

Decoder Requirements

The decoder allows scanning and decoding upon receipt of this command.

Note:

At initial power-up, the decoder should assume SCAN_ENABLED.

Length

Opcode

Message Source

Status

Data

Checksum

0x04

0xE9

0x04

Field Name

Format

Size

Description

Length 

Length of message (not 
including checksum).

1 Byte

Length Field

Opcode

0xE9

1 Byte

Identifies this Opcode type.

Message 
Source

4 = Host

1 Byte

Identifies where the message is 
coming from.

Status

Bit 0: Retransmit
Bit 1-7: Unused

1 Byte

Identifies the transmission status.
Unused bits must be set to 0.

Data

None

Checksum

2's complement sum of 
message contents 
excluding checksum.

2 Bytes

Checksum of message.

Содержание SE 923















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды