manualshive.com logo in svg

Sym GTS 250, Руководство по обслуживанию

Поделиться
Скачать
Sym GTS 250 Скачать руководство пользователя страница 6

 

1. General Information

 

1-1 

 

Symbols and Marks····························1-1

 

General Safety ····································1-2

 

Service Precautions ···························1-3

 

Specifications ·····································1-9 

Torque Values ···································· 1-10

 

Troubles Diagnosis···························· 1-12

 

Lubrication Points ····························· 1-16 

 

Symbols and Marks 

Symbols and marks are used in this manual to indicate what and where the special service are needed, in 
case supplemental information is procedures needed for these symbols and marks, explanations will be 
added to the text instead of using the symbols or marks. 

 

 Warning 

Means that serious injury or even death may result if procedures are not 
followed. 

 Caution 

Means that equipment damages may result if procedures are not followed.

 Engine 

oil 

Limits to use SAE 10W-30 API SG class oil.    Warranty will not cover the 
damage that caused by not apply with the limited engine oil. 
(Recommended oil: KING MATE G-3 oil) 

  Grease 

King Mate G-3 is recommended. 

 Gear 

oil 

King Mate gear oil serials are recommended. (Bramax HYPOID GEAR OIL 
# 140) 

 Locking sealant 

Apply sealant; medium strength sealant should be used unless otherwise 
specified. 

 Oil seal 

Apply with lubricant.

。

 

 Renew 

Replace with a new part before installation. 

 Brake fluid 

Use recommended brake fluid DOT3 or WELLRUN brake fluid. 

 Special tools 

Special tools 

 Correct 

Meaning correct installation. 

 Wrong 

Meaning wrong installation. 

  Indication 

Indication of components. 

 Directions 

Indicates position and operation directions 

 

Components assembly directions each other. 

 

Indicates where the bolt installation direction, --- means that bolt cross 
through the component (invisibility). 

 

1

 

Homepage 

Contents 

Содержание GTS 250


























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды