manualshive.com logo in svg

Sym GTS 250, Руководство по обслуживанию

Поделиться
Скачать
Sym GTS 250 Скачать руководство пользователя страница 32

 

2. Maintenance Information 

2-11

 

 

Disk Brake System 

Brake System Hose 

Make sure the brake hoses for corrosion or 
leaking oil. 

 
 
 
 

Brake Fluid 

Check brake fluid level in the brake fluid reservoir. 
If the level is lower than the 

LOWER

 limit, add 

brake fluid to UPPER limit. Also check brake 
system for leaking if low brake level found 

 Caution 

y

 In order to maintain brake fluid in the reservoir 

in horizontal position, do not remove the cap 
until handle stop. 

y

 Do not operate the brake lever after the cap 

had been removed.    Otherwise, the brake 
fluid will spread out if operated the lever. 

y

 Do not mix non-compatible brake fluid 

together. 

Filling Out Brake Fluid 

Tighten the drain valve, and add brake fluid. 
Operate the brake lever so that brake fluid 
contents inside the brake system hoses. 
 

Added Brake Fluid 

Add brake fluid to UPPER limit lever. 
Recommended brake fluid: DOT3 or DOT4 WELL 
RUN brake fluid. 

 Caution 

Never mix or use dirty brake fluid to prevent from 
damage brake system or reducing brake 
performance. 

 

Air Bleed Operation 

Connect a transparent hose to draining valve. 
Hold the brake lever and open air bleeding valve. 
Perform this operation alternative until there is no 
air inside the brake system hoses. 

 Caution 

Before closing the air bleed valve, do not release 
the brake lever. 

 

 

 

 

 

 

 

 

 

Transparent hose

Air bubble 

Drain valve

Master cylinder cap 

LOWER 

Diaphragm 

Brake 
Fluid 

To this chapter contents

Содержание GTS 250


























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды