Sym GTS 250 Скачать руководство пользователя страница 184

Страница: 184 / 217

15. Steering / Front Wheel / Front Cushion

15-9

Steering Stem

Remove

Remove handle, front wheel and front cushion.
Remove the steering stem mounting nut.

Remove top cone race and steering stem.

Caution

Place the steel ball onto a parts container to

prevent from missing.

Special tools:
Steering stem top thread wrench SYM-5320010
Handle stand nut wrench

SYM-5321100

Slightly tap the top and bottom ball bearing seats
with a plastic hammer to remove the seats.
Remove bottom cone race body with a punch.

Caution

Do not damage the steering stem.

Installation

Install a new bottom cone race onto the steering
stem.
Push the cone race until to mounted position.

Caution

Do not tilt the ball bearing seats as

installation.

Apply with grease onto the ball bearing seats, and
install steel balls onto the seats.(Top: 26 balls,
bottom: 29 balls)

Stem mounting nut

Top cone race

Steering stem mounting nut

Bottom cone race

Steel balls

Top cone race

Top ball
bearing seat

Bottom ball
bearing seat

Steering stem top

thread wrench

Top cone race

Handle stand nut wrench

To this chapter contents

Содержание GTS 250


























































































































































































































Результаты поиска

Содержание GTS 250

Отзывы:

Sym GTS 250, Руководство по обслуживанию, Страница: 184 / 217

Результаты поиска

Содержание GTS 250

Отзывы: