manualshive.com logo in svg

Sym GTS 250, Руководство по обслуживанию

Поделиться
Скачать
Sym GTS 250 Скачать руководство пользователя страница 151

13. Body Cover 

 

13-2 

 

Maintenance 

Body covers disassemble sequence: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

y

 

Be careful not to damage various covers in assembly or disassembly operation. 

y

 

Never injure hooks molded on the body covers. 

y

 

Align the buckles on the guards with slot on the covers. 

y

 

Make sure that each hook is properly installed during the assembly. 

y

 

Never compact forcefully or hammer the guard and the covers during assembly. 

 

Rear fender 

Under cover 

R/L. Handle covers 

Floor panel 

Handle upper cover 

Inner box 

Luggage box & seat 

Front fender 

Wind screen 

Meter visor 

Front cover 

Meter panel

 

Front under spoiler

 

Wind screen garnish 

Rear carrier 

R/L. side cover 

R/L body cover 

R/L. side cover 

Rear mudguard 

To this chapter contents 

Содержание GTS 250


























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды