Sym GTS 250 Скачать руководство пользователя страница 114

Страница: 114 / 217

9. Final Driving Mechanism

9-5

Bearing Replacement

Left crankcase side

If the drive shaft is pulled out with its bearing, then
remove the bearing with bearing puller and shaft
protector.

Special tool:
Multi-functional bearing puller or Outer bearing
puller SYM-6204001
Shaft protector

SYM-6204010

Remove final shaft bearing and counter shaft
bearing from left crankcase using following tools.

Special tool:
Inner bearing puller SYM-6204020 or

SYM-6204021

Caution

Never install used bearings. Once bearing

removed, it has to be replaced with new one.

Install new final shaft bearing and counter shaft
bearing into left crankcase.

Special tool:
Bearing driver 6205

SYM-9615000-6205

Bearing driver HK1516 SYM-9100200-HK1516

Install new drive shaft bearing and bearing puller
onto left crankcase.

Special tool:
Bearing puller 6205

SYM-9100400-6205

Outer bearing puller

Inner bearing

puller

Bearing driver

Bearing puller 6205

To this chapter contents

Содержание GTS 250


























































































































































































































Результаты поиска

Содержание GTS 250

Отзывы:

Бренды по названию

Популярные бренды

Sym GTS 250, Руководство по обслуживанию

Результаты поиска

Содержание GTS 250

Отзывы:

Бренды по названию

Популярные бренды