manualshive.com logo in svg

Sym GTS 250, Руководство по обслуживанию

Поделиться
Скачать
Sym GTS 250 Скачать руководство пользователя страница 112

 

9. Final Driving Mechanism 

9-3 

 

Disassembly of Final Driving 
Mechanism 

Remove the rear wheel. 
Remove the clutch. 
Drain out gear oil from gear box. 
Loosen 7 bolts and remove gear box cover bolts. 
 
 
 
 
 
 
 
Remove the gear box cover, counter shaft and 
final shaft. 
Remove the gasket & dowel pin. 

 
 
 
 
 
 
 
 
 
 
 

Remove final gear. 
Remove counter shaft, gear and 2 washers. 
Remove final shaft. 

 
 
 
 
 
 
 
 
 
 

Remove the drive shaft. 

Special tool: 
Shaft protector 

 Caution 

y

  If non- essential do not remove the drive 

shaft from the cover upper side.

 

y

  If remove the drive shaft from the gear box 

cover, then its bearing has to be replaced.

 

 

 

 

 

 

 

 

 

7 bolts

Drive shaft

Final shaft

Counter shaft

To this chapter contents

Содержание GTS 250


























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды