manualshive.com logo in svg

Sykes-Pickavant 02683000 - LV, Инструкция по эксплуатации, Страница: 5 / 10

Поделиться
Скачать
Sykes-Pickavant 02683000 - LV Скачать руководство пользователя страница 5

 

 

5 

 

 
 
COMPLEX SYSTEMS INCLUDING XENON AND BI-XENON HEADLIGHT 
SYSTEMS 

 

It is essential that this equipment is aligned exactly on the centre line of the dipped beam 
pocket. 
If when carrying out a normal test/adjustment a clearly defined headlamp pattern cannot be 
seen, it will be necessary to move the vehicle closer to the test equipment. 
It is essential that the vehicle headlamp and test equipment are as close together as possible.  

 

 
TESTING HEADLAMPS WITH COMPLEX LENS SYSTEMS. 

 

Complex headlamp systems are those that have more than one lamp behind a single lens. 
It is essential that the headlamp aim test equipment is aligned exactly on the centre of the 
dipped beam pocket. 
If when carrying out a normal test a clearly defined headlamp pattern cannot be seen, it will 
be necessary to move the vehicle closer to the test equipment. 
It is essential that the car headlamp and test equipment are as close together as possible, 
otherwise the whole of the beam pattern may not be visible. 

 

EUROPEAN TYPE HEADLAMP CHARACTERISTICS

  (NOTE:1)

 

 

An asymmetric dipped beam, pattern with a distinctive horizontal cut-off on the right, and a 
15 degree wedge of light above the horizontal (the “Kick up”) towards the left. 
A lens with one or more asymmetric stepped patterns molded in the glass. 
A lens may carry: 
European approval mark – a circle containing an “E” and a number, or 
Rectangle containing an “e”, and a number 

 

The European approval mark should incorporate a single or double-headed arrow. 
 
The dipped beam is denoted by either: 
Capital letter “C” above a capital “E” 
Capital letter “C” above an “e” 
 

NOTE:

 Setting “E” Beam Headlamp aim 

These dip-beam headlamps should be set to aim downwards the amount shown on a 
marking which is either close to the vehicle manufacturer’s plate or the headlamp. 
 
For vehicles without a marking, the downward aim should be set as follows: 
1,3%, if the headlamp centre is not more than 850mm from the ground 
2.0%, if the headlamp centre is more than 850mm from the ground 

 
Reason for rejection 
 

The beam image “Kick-up” is to the offside. 

 

Содержание 02683000 - LV











Отзывы:

Нет отзывов