Sykes-Pickavant 02683000 - LV Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 10

Sykes-Pickavant 02683000 - LV Скачать руководство пользователя страница 3

3

GENERAL REGULATIONS

Carefully read the instructions in this manual, before using the headlight beam tester. Do not
allow unqualified persons to use this device.  The workplace should be dry, well lit  and
ventilated. Working  areas should be equipped with an exhausts gas  aspirator, since the
headlight tester must be used with the engine running. Breathing carbon monoxide can be
harmful.  Put the handbrake on. Do not use the device in  direct sunlight  and  avoid sudden
changes of temperature and vibrations.

DESCRIPTION OF THE DEVICE

Headlight beam tester (HBT): Suitable for all headlight types including Xenon
Supplied with:
-

Turning column

-

Mirror-visor

-

Luxmeter

TECHNICAL CHARACTERISTICS:

Column Height: 166 cm.
Width: 61 cm.
Length: 61 cm.

MOT Approved Headlight Beam Tester - LV (02683000)

Includes a kit to make 2 x 3.75 metre rails (4 x 1.50m + 2 x 0.75m)

MOT Approved Headlight Beam tester - HGV (02688000)

Includes a kit to make 2 x 5.2 metre rails (6 x 1.50m + 2 x 0.70m)

MAXIMUM MEASUREMENT HEIGHT: 141 CM.

Minimum measurement height: 24 cm.
Focal length: 500 mm.

PACKING

The HBT is delivered in a recycled carton box.

HEADLIGHT BEAM TESTER ASSEMBLY

Fix the column with 4 screws
Fix the optical box with the screw and the lever
Fix the mirror-visor with two screws
The stand is calibrated and locked in the correct position at the moment of test

«
1
2
3
4
5
...
»

Содержание 02683000 - LV











Отзывы:

Нет отзывов