manualshive.com logo in svg

Swarts Tools SW1045, Инструкция пользователя, Страница: 13 / 16

Поделиться
Скачать
Swarts Tools SW1045 Скачать руководство пользователя страница 13

INSTRUCTION BOOKLET

INSTRUCTION BOOKLET

INSTRUCTION BOOKLET

INSTRUCTION BOOKLET

13

4. 

Use the clamp assembly (10) to secure the work piece wherever possible. It is possible to remove the clamp 

assembly (10) by loosening the clamp assembly lock (11) and moving it to the other side of the table. Make sure 

the clamp assembly lock is tight before using the clamp. Before turning on the saw, perform a dry run of the cutting 

operation to check that there are no problems.

5. 

Hold the operating handle (7) firmly and squeeze the switch trigger (24). Allow the blade to reach maximum speed.

 

Press the release latch (35) and slowly lower the blade into and through the work piece. Release the switch trigger (24) 

and allow the saw blade to stop rotating before raising the blade out of the work piece. Wait until the blade stops before 

removing the work piece.

CROSS-CUTTING (WITH SLIDE ACTION)

When cutting wide work pieces, first unscrew the slide lock (29). Pull on the release knob (6), raise the saw arm (5) to its 

highest position and slide it towards you. Hold the handle firmly and squeeze the switch trigger (24). 

 

Allow the blade to reach maximum speed. Press the release latch (35) and slowly lower the blade into the work piece 

and slide it away from you at the same time until the work piece is cut. Release the switch trigger (24) and allow the saw 

blade to stop rotating before raising the blade out of the work piece. Wait until the blade stops before removing the work 

piece.

 

BEVEL CUT

A bevel cut is made by cutting across the grain of the work piece with the blade angled to the fence and mitre table. 

1. The mitre table is set at the zero degree position and the blade set at an angle between 0 degrees and 45 degrees. 

Use the slide action when cutting wide work pieces. 

2. Loosen the bevel lock (16) and move the saw arm (5) to the left of the desired bevel angle (between 0 degrees and 45 

degrees).

3. Tighten the bevel lock.

4. To Do right bevel cuts release bevel lock (16), tilt the saw arm  (5) slightly left and pull the positive stop knob (39) then 

tilt back the saw arm (5) right.

COMPOUND MITRE CUT

A compound mitre cut involves using a mitre angle and a bevel angle at the same time. It is used in the manufacture 

Содержание SW1045

















Отзывы:

Нет отзывов