manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

8B-114 Air Bag System: 

4) Install head lining referring to “Head Lining Removal 

and Installation:  in Section 9H”.

5) Enable air bag system. Refer to “Enabling Air Bag 

System: ”.

Side Curtain-Air Bag (Inflator) Module 
Inspection

S4RS0A8206026

WARNING:

• Never measure resistance of side curtain-

air bag (inflator) module or disassemble it. 
Otherwise personal injury may result.

• Never attempt to disassemble or repair the 

side curtain-air bag (inflator) module. If any 
abnormality is found, be sure to replace it 
with new one as an assembly.

• Be sure to read “Precautions on Service 

and Diagnosis of Air Bag System: ”, 
“Precautions on Handling and Storage of 
Air Bag System Components: ” and 
“Precautions on Disposal of Air Bag and 
Seat Belt Pretensioner: ” before starting to 
work and observe every precaution during 
work. Neglecting them may result in 
personal injury or undeployment of the air 
bag when necessary.

 

CAUTION:

If air bag (inflator) module was dropped from 
a height of 90 cm (3 ft) or more, it should be 
replaced.

 

Check air bag (inflator) module appearance visually for 
the following symptoms and if any one of them is found, 
replace with a new one.
• Air bag has deployed.
• Inflator case being damaged or having been exposed 

to strong impact (dropped).

Forward-Sensor Removal and Installation

S4RS0A8206009

WARNING:

During service procedures, be very careful 
when handling a sensor.
• Never strike or jar a sensor.
• A sensor and mounting bracket bolts must 

be carefully torqued to assure proper 
operation. Under loose connection, it 
could cause improper operation of the air 
bag system.

 

Removal

1) Disconnect negative cable at battery.
2) Disable air bag system referring to “Disabling Air 

Bag System: ”.

3) Disconnect forward-sensor connector sliding 

connector outer (2) as shown.

1

2

a)

b)

I4RS0A820055-

I4RS0A820078-

1

2

I4RS0A820079-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Abarth 595 Owner'S Handbook Manual preview
595
Бренд: Abarth Страницы: 176
Dakota Digital VHX-37F Installation preview
VHX-37F
Бренд: Dakota Digital Страницы: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Бренд: Dakota Digital Страницы: 7
FANATEC Porsche 911 Turbo S Wheel Developer Quick Manual preview
Porsche 911 Turbo S Wheel
Бренд: FANATEC Страницы: 9
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Бренд: Toyota Страницы: 19
BMW 3-series convertible Complete Vehicle Workbook preview
3-series convertible
Бренд: BMW Страницы: 98
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Бренд: PUTCO Страницы: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Бренд: Westfalia Страницы: 18
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Бренд: Victory 4x4 Страницы: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Бренд: Keith Страницы: 2
MAXWORKS 70275 Instruction Manual & Parts Catalogue preview
70275
Бренд: MAXWORKS Страницы: 7
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Бренд: muth Страницы: 9
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Бренд: Renault Страницы: 183
Chevrolet 1999 Malibu Owner'S Manual preview
1999 Malibu
Бренд: Chevrolet Страницы: 344
Prorack K692 Fitting Instructions Manual preview
K692
Бренд: Prorack Страницы: 15
Yakima Landing Pad 24 Quick Start Manual preview
Landing Pad 24
Бренд: Yakima Страницы: 11
Icom RMK-5 Instruction Manual preview
RMK-5
Бренд: Icom Страницы: 20
GMC 2013 GMC Savana Owner'S Manual preview
2013 GMC Savana
Бренд: GMC Страницы: 398

Бренды по названию

Популярные бренды

Загрузить еще бренды