manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Air Bag System:  8B-99

NOTE:
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components, ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance: ”, if any.
• Repeat “Air Bag Diagnostic System Check: ” to confirm that the trouble has been corrected.

 

DTC B1364 / B1368: Driver / Passenger Side Curtain-Air Bag Initiator Circuit Short to Power Circuit

S4RS0A8204086

Wiring Diagram

2

1) With ignition switch OFF, disconnect SDM connector 

“L29”.

2) Release shorting bar in SDM connector inserting release 

tool (1) included in special tool (A).

3) Measure resistance between “L29-18” and body ground, 

and between “L29-19” and body ground (for DTC 
B1363) or “L29-20” and body ground, and between “L29-
21” and body ground (for DTC B1367) with connected 
special tools (A), (B) and (C).

Special tool
(A):  09932–76010
(B):  09932–75010
(C):  09932–78310

Is resistance infinity?

Substitute a known-
good SDM and recheck.

DTC B1363: Repair 
short from “RED/BLU” 
or “YEL/BLK” wire 
circuit to ground.
DTC B1367: Repair 
short from “BLU/RED” 
or “BLU/YEL” wire 
circuit to ground.

Step

Action

Yes

No

"L29-19""L29-20""L29-21"

"L29-18"

STEERING WHEEL

(B)

(C)

(A)

"L17", "L41"

(A)

I4RS0A820098-

1

2

3

GRN

RED

8

BLK

L29-26

L29-27

IG

E1

4

“L29”

“L04”

“G32”

“L29”

L29-19

DC+

L29-18

DC-

YEL/BLK

RED/BLU

5

6

“L17”

L29-20

PC+

L29-21

PC-

BLU/YEL

BLU/RED

7

“L41”

[A]

I4RS0A820095-

[A]: Shorting bar

3. “A/BAG” fuse

6. Driver side curtain-air bag (inflator) module

1. From main fuse

4. Junction block assembly

7. Passenger side curtain-air bag (inflator) module

2. Ignition switch

5. SDM

8. Ground for air bag system

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Kia Sorento Owner'S Manual preview
Sorento
Бренд: Kia Страницы: 51
Cadillac 2004 ESCALADE Customer Convenience/Personalization Manual preview
2004 ESCALADE
Бренд: Cadillac Страницы: 20
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Бренд: Carcomm Страницы: 2
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Бренд: r.LiNK Страницы: 21
Safe Fleet Prime Design VBI-FT31B Assembly Instructions Manual preview
Prime Design VBI-FT31B
Бренд: Safe Fleet Страницы: 12
Havis-Shields Telescoping Computer Base C-TCB-34 Install Instructions preview
Telescoping Computer Base C-TCB-34
Бренд: Havis-Shields Страницы: 1
PEUGEOT 106 2001 Owner'S Manual preview
106 2001
Бренд: PEUGEOT Страницы: 107
Green Valley 601951 Instructions Manual preview
601951
Бренд: Green Valley Страницы: 17
Ford C-Max Energi 2014 Quick Reference Manual preview
C-Max Energi 2014
Бренд: Ford Страницы: 10
Honda Vezel Owner'S Manual preview
Vezel
Бренд: Honda Страницы: 279
Yakima K682 Instructions Manual preview
K682
Бренд: Yakima Страницы: 10
Chevrolet 2001 Cavalier Owner'S Manual preview
2001 Cavalier
Бренд: Chevrolet Страницы: 357
A-Tach Mounts 50321 Quick Start Manual preview
50321
Бренд: A-Tach Mounts Страницы: 2
Thule 2087 Parts List preview
2087
Бренд: Thule Страницы: 1
Whispbar K477W Fitting Instructions Manual preview
K477W
Бренд: Whispbar Страницы: 15
Prorack K890 Fitting Instructions Manual preview
K890
Бренд: Prorack Страницы: 15
Mazda MVG 4507 F Installation Instruction preview
MVG 4507 F
Бренд: Mazda Страницы: 38
Champion Power Equipment 14560 Owner'S Manual & Operating Instructions preview
14560
Бренд: Champion Power Equipment Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды