manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Manual Transmission:  5B-14

Fifth Gear Disassembly and Assembly

S4RS0A5206018

Disassembly

1) Remove 9 bolts and take off transaxle side cover (1).

CAUTION:

Care should be taken not to distort side cover 
when it is removed from left case.

 

2) Using special tool, remove circlip (1).

Special tool
:  09900–06107

3) Remove 5th shift fork bolt (2).
4) Remove gear shift fork (3), synchronizer sleeve & 

hub assembly (4), synchronizer levers, synchronizer 
ring and input shaft 5th gear (5) all together. Use 
gear puller for removal if spline fitting of hub is tight.

5) Unfasten caulking of countershaft nut (2), install 

input shaft 5th gear (1) and special tool to stop 
rotation of shafts, and then remove countershaft nut 
(2).

Special tool
(A):  09927–76060

1. Transaxle right case

25. 5th gear shift fork

2. Transaxle left case

: Apply sealant 99000-31260 to mating surface of left case and right 
case.

26. Needle bearing (Separated steel cage type.)

3. Gear shift and select shaft assembly

27. Input shaft 5th gear

4. Transaxle left case plate

28. Reverse gear shift lever

5. Transaxle side cover

: Apply sealant 99000-31260 to mating surface of side cover and left 
case.

29. Reverse gear shift lever bolt

: Apply thread lock 99000-32110 to all around thread part of bolt.

6. Back up lamp switch

30. Reverse gear shaft

7. O-ring

31. Washer

8. Differential assembly

32. Reverse idler gear

9. Oil level/filler plug

: Apply sealant 99000-31260 to all around thread part of plug.

33. Reverse shaft bolt

: Apply thread lock 99000-32110 to all around thread part of bolt.

10. Oil drain plug

: Apply sealant 99000-31260 to all around thread part of plug.

34. Washer

11. VSS

35. Side bearing retainer

12. Oil gutter bolt

: Apply thread lock 99000-32110 to all around thread part of bolt.

36. O-ring

13. Left case plate bolts

: Apply thread lock 99000-32110 to all around thread part of bolt.

37. Oil seal

: Apply grease 99000-25010 to oil seal lip.

14. VSS bolt

38. Outer race

15. Side cover bolts

39. Breather hose

16. Transaxle case bolts

40. Side bearing retainer bolt

17. 5th speed synchronizer ring

: 23 N

˜

m (2.3 kg-m, 17.0 lb-ft)

18. 5th speed synchronizer lever

: 21 N

˜

m (2.1 kg-m, 15.5 lb-ft)

19. 5th speed synchronizer sleeve & hub

: 10 N

˜

m (1.0 kg-m, 7.5 lb-ft)

20. Circlip

: 5 N

˜

m (0.5 kg-m, 4.0 lb-ft)

21. Bearing set shim

: 100 N

˜

m (10.0 kg-m, 72.5 lb-ft)

22. Countershaft 5th gear

: Do not reuse.

23. Countershaft nut

: After tightening nut to specified torque, caulk nut securely.

: Apply transaxle oil.

 24. Shift fork bolt

: Apply thread lock 99000-32110 to all around thread part of bolt.

I4RS0A520027-

3

4

2

1

5

I4RS0A520028-

1

(A)

2

I3RM0B521014-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Ecco EW4010 Installation And Operation Instructions Manual preview
EW4010
Бренд: Ecco Страницы: 9
Ecco EW4009 Installation And Operation Instructions Manual preview
EW4009
Бренд: Ecco Страницы: 9
TATA Motors Indigo Owner'S Manual & Service Book preview
Indigo
Бренд: TATA Motors Страницы: 164
Yakima K800 Instructions Manual preview
K800
Бренд: Yakima Страницы: 8
Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Бренд: Genesis Страницы: 3
Chevrolet Avalanche 2005 Owner'S Manual preview
Avalanche 2005
Бренд: Chevrolet Страницы: 494
Code 3 WingMan Installation & Operation Manual preview
WingMan
Бренд: Code 3 Страницы: 8
Trailboss QTHD519L Fitting Instructions Manual preview
QTHD519L
Бренд: Trailboss Страницы: 8
Metra Electronics 95-8202 Installation Instructions Manual preview
95-8202
Бренд: Metra Electronics Страницы: 20
Fast Master Products SWIVELWHEEL-46 Assembly Instructions Manual preview
SWIVELWHEEL-46
Бренд: Fast Master Products Страницы: 13
Yutrax TX107 Operator'S Manual preview
TX107
Бренд: Yutrax Страницы: 8
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
Toyota SUPRA 1987 Electrical Wiring Diagram preview
SUPRA 1987
Бренд: Toyota Страницы: 165
v.link VL2-MBN2 Manual preview
VL2-MBN2
Бренд: v.link Страницы: 12
TATA Motors INDICA eV2 XETA CNG Supplemental Owner'S Manual preview
INDICA eV2 XETA CNG
Бренд: TATA Motors Страницы: 24
PAC AP4-GM61 Quick Start Manual preview
AP4-GM61
Бренд: PAC Страницы: 5
Percon Falcon 655 User Manual preview
Falcon 655
Бренд: Percon Страницы: 49
Arrista SG8-19 Installation Manual preview
SG8-19
Бренд: Arrista Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды