manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-162 Automatic Transmission: 

69) After applying A/T fluid to cooler check valve (1) and 

spring (2), install them to transaxle case (3).

70) After applying A/T fluid to new governor apply No.1 

gasket (1), install it to transaxle case.

71) After applying A/T fluid to new O-ring, fit it to valve 

body harness connector (3), then install valve body 
harness to transaxle case.

CAUTION:

When put valve body harness (1) into 
transaxle case, take care not to damage 
transmission fluid temperature sensor (2) at 
narrow entrance of case.
Careless sensor treatment might cause 
sensor malfunction.

 

Tightening torque
Valve body harness connector bolt (a):  5.5 N·m (
0.55 kg-m, 4.0 lb-ft)

72) Install manual valve rod (1) to manual valve lever (3) 

and then install valve body assembly (2) to transaxle 
case.

73) Tighten valve body bolts to specified torque.

Tightening torque
Valve body bolt:  11 N·m (1.1 kg-m, 8.0 lb-ft)

Valve body bolt length

I2RH0B510318-

I2RH0B510319-

I2RH0B510320-

Bolt

Length “a”

Pieces

A (1)

20 mm (0.79 in.)

6

I2RH0B510321-

I2RH0B510322-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Camoplast T4S User Manual preview
T4S
Бренд: Camoplast Страницы: 60
Fab Fours BLACK STEEL S2560 Installation Instructions Manual preview
BLACK STEEL S2560
Бренд: Fab Fours Страницы: 9
Yakima RoadShower 10G Quick Start Manual preview
RoadShower 10G
Бренд: Yakima Страницы: 12
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Бренд: Ford Страницы: 38
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Бренд: Atwood Страницы: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Бренд: BMW Страницы: 21
Wagan Wireless Handsfree Car Kit User Manual preview
Wireless Handsfree Car Kit
Бренд: Wagan Страницы: 20
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Бренд: VDO Страницы: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Бренд: Wagan Страницы: 3
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Бренд: Ford Страницы: 368
Waeco 8885100124 Operating Manual preview
8885100124
Бренд: Waeco Страницы: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Бренд: VBG Страницы: 16
Audiovox UniStreamONE Installation Manual preview
UniStreamONE
Бренд: Audiovox Страницы: 24
Mercedes-Benz GLE Coupe Brief Overview preview
GLE Coupe
Бренд: Mercedes-Benz Страницы: 2
Westin 25-0560 Instructions preview
25-0560
Бренд: Westin Страницы: 2
Menabo DELTA DL FIX 209FP Fitting Instructions Manual preview
DELTA DL FIX 209FP
Бренд: Menabo Страницы: 8
Hyundai Entourage 2008 Quick Reference Manual preview
Entourage 2008
Бренд: Hyundai Страницы: 11
THIEYE CarView 2 User Manual preview
CarView 2
Бренд: THIEYE Страницы: 88

Бренды по названию

Популярные бренды

Загрузить еще бренды