manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Front Brakes:  4B-2

Front Disc Brake Pad On-Vehicle Inspection

S4RS0A4206002

Inspect pad linings (1) periodically according to 
maintenance schedule whenever wheels are removed 
(for tire rotation or other reason). Take a look through 
each end (or hole) of caliper and check lining thickness 
of outside and inside pads.
If lining is worn and its thickness (“a” in figure) is less 
than limit, all pads must be replaced at the same time.

Front brake pad thickness “a” (lining thickness)
Standard: 10 mm (0.40 in.)
Limit: 2 mm (0.08 in.)

Front Disc Brake Pad Removal and Installation

S4RS0A4206003

Removal

1) Loosen wheel nuts and with vehicle lifted up, remove 

wheels.

2) Remove caliper pin bolts (1).

3) Remove caliper (1) from caliper carrier (2).

NOTE:
Hang removed caliper (1) with a wire hook (4) 
or the like so as to prevent brake hose from 
bending and twisting excessively or being 
pulled.
Don’t operate brake pedal with brake pads 
removed.

 

4) Remove brake pads (3).

Installation

1) Before installing brake pad shim, apply small amount 

of pad grease “a” (included in pad kit) to mating 
surfaces of brake pad (1) and pad shim (2).

WARNING:

Do not apply grease on pad lining surface.

 

2) Set brake pad springs (1) and shim (2) and install 

brake pads (3).

NOTE:
For right side brake, install pad with wear 
indicator (4) to vehicle center side.

 

I2RH01420001-

1

I2RH01420003-

I2RH01420004-

I4RS0A420005-

I2RH01420006-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Jeep Renegade Owner'S Handbook Manual preview
Renegade
Бренд: Jeep Страницы: 212
OEM Tools 22505 Operating Instructions And Parts Manual preview
22505
Бренд: OEM Tools Страницы: 4
Safe Fleet RVS-082550 Instruction Manual preview
RVS-082550
Бренд: Safe Fleet Страницы: 11
Camec 042374 User Manual preview
042374
Бренд: Camec Страницы: 19
Calitop Calispace Ocean 80 Assembly Instructions preview
Calispace Ocean 80
Бренд: Calitop Страницы: 5
Demco TP20047 Assembly Operation Replacement Parts preview
TP20047
Бренд: Demco Страницы: 4
WATT CARWATT CV12-220C150 User Manual preview
CARWATT CV12-220C150
Бренд: WATT Страницы: 26
Toyota Solara guide Owner'S Manual preview
Solara guide
Бренд: Toyota Страницы: 497
PEUGEOT BOXER 2018 Handbook preview
BOXER 2018
Бренд: PEUGEOT Страницы: 232
Westin 28-21030 Instructions preview
28-21030
Бренд: Westin Страницы: 3
Volkswagen 1963 1500 Instruction Manual preview
1963 1500
Бренд: Volkswagen Страницы: 68
KAP HK CARPLAY 10w Instruction Manual preview
HK CARPLAY 10w
Бренд: KAP Страницы: 22
Honda 2002 Accord Coupe Owner'S Manual preview
2002 Accord Coupe
Бренд: Honda Страницы: 367
Mercedes-Benz G 55 AMG Operator'S Manual preview
G 55 AMG
Бренд: Mercedes-Benz Страницы: 284
Advent MAZBTSW2 Owner'S Manual preview
MAZBTSW2
Бренд: Advent Страницы: 8
RAWLINK 36772 Instruction Manual preview
36772
Бренд: RAWLINK Страницы: 25
Fortin Electronic Systems EVO-CAN Suggested Wiring Configuration preview
EVO-CAN
Бренд: Fortin Electronic Systems Страницы: 5
TrailFX FCLR003B Assembly, Installation, Operation And Maintenance Instructions preview
FCLR003B
Бренд: TrailFX Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды