manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Rear Suspension:  2C-13

Tightening torque
Rear spindle bolt (a):  75 N·m (7.5 kg-m, 54.0 lb-
ft)

2) Connect wheel speed sensor (1) and tighten wheel 

speed sensor bolt (a) to specified torque.

Tightening torque
Wheel speed sensor bolt (a):  11 N·m (1.1 kg-m, 
8.0 lb-ft)

3) Connect brake pipes to wheel cylinder (1) and 

tighten brake pipe flare nut (a) to specified torque.

Tightening torque
Brake pipe flare nut (a):  16 N·m (1.6 kg-m, 11.5 
lb-ft)

4) Install brake drum referring to Steps 2) – 7) of “Rear 

Brake Drum Removal and Installation:  in Section 
4C”.

5) Fill reservoir with brake fluid and bleed brake 

system. For bleeding operation, see “Air Bleeding of 
Brake System:  in Section 4A”.

6) Install wheel and tighten wheel nuts to specified 

torque.

Tightening torque
Wheel nut (a):  85 N·m (8.5 kg-m, 61.5 lb-ft)

7) Upon completion of all jobs, depress brake pedal 

with about 300 N (30 kg, 66 lbs) load three to five 
times so as to obtain proper drum-to-shoe clearance.
Adjust parking brake cable. For adjustment, see 
“Parking Brake Inspection and Adjustment:  in 
Section 4D”.

8) Check to ensure that brake drum is free from 

dragging and proper braking is obtained.

9) Perform brake test (foot brake and parking brake).

10) Check each installed part for fluid leakage.

Spindle Inspection

S4RS0A2306045

• Inspect for cracks, deformation or damage.

Replace any defective part.

Rear Suspension Fasteners Inspection

S4RS0A2306025

Check each bolt and nut fastening suspension parts for 
tightness. Tighten loose one, if any, to specified torque 
referring to the figure in “Rear Suspension Component 
Location: ”.

I4RS0A230025-

1

(a)

I4RS0A230041-

(a)

1

I4RS0A230027-

I2RH01220009-

I4RS0A230042-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Safe Fleet PRIME DESIGN VCR 326 Assembly Instructions Manual preview
PRIME DESIGN VCR 326
Бренд: Safe Fleet Страницы: 16
Safe Fleet Prime Design VBC PC11 Quick Start Manual preview
Prime Design VBC PC11
Бренд: Safe Fleet Страницы: 8
Safe Fleet Prime Design AR1418 Manual preview
Prime Design AR1418
Бренд: Safe Fleet Страницы: 4
APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Бренд: APS Auto Parts Specialist Страницы: 3
Dometic PERFECTVIEW CAM80AHD Installation And Operating Manual preview
PERFECTVIEW CAM80AHD
Бренд: Dometic Страницы: 196
Tessera4x4 SOT-1311 ROLL Installation Manual preview
SOT-1311 ROLL
Бренд: Tessera4x4 Страницы: 20
MAXWORKS 70275 Instruction Manual & Parts Catalogue preview
70275
Бренд: MAXWORKS Страницы: 7
AA Products RB0007 Instruction Manual preview
RB0007
Бренд: AA Products Страницы: 6
Van Guard VG273 Fitting Instructions preview
VG273
Бренд: Van Guard Страницы: 3
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Бренд: Dakota Digital Страницы: 3
METRON PC05T User Manual preview
PC05T
Бренд: METRON Страницы: 4
Cadillac 2003 Seville Owner'S Manual preview
2003 Seville
Бренд: Cadillac Страницы: 402
Cobra BAK R294 Manual preview
BAK R294
Бренд: Cobra Страницы: 2
Jaeger 21010508J Fitting Instructions Manual preview
21010508J
Бренд: Jaeger Страницы: 14
Chrysler Sebring Convertible Owner'S Manual preview
Sebring Convertible
Бренд: Chrysler Страницы: 454
PEUGEOT 208 T16 User Manual preview
208 T16
Бренд: PEUGEOT Страницы: 67
AA Products APX2501 BLK Instruction Manual preview
APX2501 BLK
Бренд: AA Products Страницы: 8
injen technology SP7035 Installation Instructions preview
SP7035
Бренд: injen technology Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды