manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

2C-12 Rear Suspension: 

Rear Wheel Disc, Nut and Bearing Inspection

S4RS0A2306021

• Check wheel nuts for tightness and, as necessary, 

retighten to specification.

• Check wheel bolt press-fitted into brake drum for 

wear, damage, poor thread condition, and looseness.
Replace defective bolt with a new one.
When bolt installation is found loose, replace both bolt 
and brake drum with new ones.

• Check wheel disc for deformation, damage, crack, 

etc.
Replace defective disc with a new one.

• Check installation face inside of wheel disc for rust.

As rust affects adversely, remove it thoroughly.

Tightening torque
Wheel nut (a):  85 N·m (8.5 kg-m, 61.5 lb-ft)

• Check wheel bearings for wear. When measuring 

thrust play, apply a dial gauge to axle shaft center. 
When measurement exceeds limit, replace bearing.

Thrust play limit
“a”: 0.1 mm (0.004 in.)

• By rotating wheel actually, check wheel bearing for 

noise and smooth rotation. If it is defective, replace 
bearing.

Spindle Removal and Installation

S4RS0A2306044

Removal

1) Remove brake drum referring to “Rear Brake Drum 

Removal and Installation:  in Section 4C”.

2) Disconnect brake pipe flare nut (1) from wheel 

cylinder (3) and put bleeder plug cap (4) onto pipe 
(2) to prevent fluid from spilling.

CAUTION:

Do not allow brake fluid to get on painted 
surfaces.

 

3) Disconnect wheel speed sensor (5).
4) Remove brake back plate (6) and spindle from rear 

axle and hang removed brake back plate with a wire 
hook.

Installation

1) Install brake back plate (1), spindle (2) and new 

spindle bolts (a) and then tighten spindle bolts (a) to 
specified torque.

CAUTION:

Do not reuse (reinstall) removed rear spindle 
bolts (a).

 

I4RS0A230039-

I3RM0A230049-

I3RM0A230050-

1

2

4

6

5

3

I4RS0A230040-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Federal Signal Corporation 7000 Assembly Instructions Manual preview
7000
Бренд: Federal Signal Corporation Страницы: 13
Camcar 40104 Mounting Instructions preview
40104
Бренд: Camcar Страницы: 6
Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Бренд: Gardigo Страницы: 36
Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Бренд: Bimmer Jakes Страницы: 4
femkes Hopper on Top User Manual preview
Hopper on Top
Бренд: femkes Страницы: 7
Ford 2004 Freestar Workshop Manual preview
2004 Freestar
Бренд: Ford Страницы: 8
Intec CVD500LCD Installation And Operation Manual preview
CVD500LCD
Бренд: Intec Страницы: 16
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Бренд: Ecco Страницы: 12
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Бренд: ULTIMATE SPEED Страницы: 50
Volvo 2006 XC70 Owner'S Manual preview
2006 XC70
Бренд: Volvo Страницы: 211
Kleinn RS-GM6 Installation Manual preview
RS-GM6
Бренд: Kleinn Страницы: 8
Axxess OESWC-LAN29H Installation Instructions Manual preview
OESWC-LAN29H
Бренд: Axxess Страницы: 8
Reimo TOUR EASY 4 936550 Quick Start Manual preview
TOUR EASY 4 936550
Бренд: Reimo Страницы: 4
Speedtech 64-67 Instructional Manual preview
64-67
Бренд: Speedtech Страницы: 12
Cadillac CTS 2011 Manual preview
CTS 2011
Бренд: Cadillac Страницы: 78
Phonocar 6/946 Instruction Manual preview
6/946
Бренд: Phonocar Страницы: 4
Van Guard VG162S Fitting Instructions preview
VG162S
Бренд: Van Guard Страницы: 3
Dodge 2008 Dakota Owner'S Manual preview
2008 Dakota
Бренд: Dodge Страницы: 439

Бренды по названию

Популярные бренды

Загрузить еще бренды