manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine Mechanical:  1D-44

Pistons, Piston Rings, Connecting Rods and 
Cylinders Removal and Installation

S4RS0A1406030

Removal

1) Remove engine assembly from vehicle referring to 

“Engine Assembly Removal and Installation: ”.

2) Remove cylinder head referring to “Valves and 

Cylinder Head Removal and Installation: ”.

3) Mark cylinder number on all pistons, connecting rods 

and connecting rod caps using silver pencil or quick 
drying paint.

4) Remove rod bearing caps.
5) Install guide hose (1) over threads of rod bolts.

This prevents damage to bearing journal and rod bolt 
threads when removing connecting rod.

6) Decarbonize top of cylinder bore before removing 

piston from cylinder.

7) Push piston and connecting rod assembly out 

through the top of cylinder bore.

Installation

1) Apply engine oil to pistons, rings, cylinder walls, 

connecting rod bearings and crank pins.

NOTE:
Do not apply oil between connecting rod and 
bearing or between bearing cap and bearing.

 

2) Install guide hoses (1) over connecting rod bolts.

These guide hoses protect crank pin and threads of 
rod bolt from damage during installation of 
connecting rod and piston assembly.

3) When installing piston and connecting rod assembly 

into cylinder bore, point front mark (1) on piston head 
to crankshaft pulley side.

4) Install piston and connecting rod assembly into 

cylinder bore. Use special tool (Piston ring 
compressor) to compress rings. Guide connecting 
rod into place on crankshaft.
Using a hammer handle, tap piston head to install 
piston into bore. Hold ring compressor firmly against 
cylinder block until all piston rings have entered 
cylinder bore.

Special tool
(A):  09916–77310

5) Install bearing cap (1):

Point arrow mark (2) on cap to crankshaft pulley 
side.
After applying engine oil to rod bolts and tighten cap 
nuts (3) gradually as follows.
a) Tighten all cap nuts to 15 N

˜

m (1.5 kg-m, 11.0 lb-

ft).

b) Retighten them to 45

q

c) Repeat Step b) once again.

I2RH0B140109-

I2RH01140147-

A: Crankshaft pulley side
B: Flywheel side

I2RH0B140110-

I2RH0B140111-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Blue Ox BX3781 Installation Instructions Manual preview
BX3781
Бренд: Blue Ox Страницы: 7
Shad NADSA ATV80 Owner'S Manual preview
NADSA ATV80
Бренд: Shad Страницы: 3
Pyle PLCMRV8B Black User Manual preview
PLCMRV8B Black
Бренд: Pyle Страницы: 4
TAUBENREUTHER 29-T080301 Quick Start Manual preview
29-T080301
Бренд: TAUBENREUTHER Страницы: 8
FALCON RIDGE HO-P500-FC04 Instructions For Installation And Care preview
HO-P500-FC04
Бренд: FALCON RIDGE Страницы: 8
Scosche 142HUD2 Manual preview
142HUD2
Бренд: Scosche Страницы: 8
BMW M5 2014 Service And Warranty Information preview
M5 2014
Бренд: BMW Страницы: 38
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Бренд: SCC Страницы: 4
Subaru 1998 Forester Owner'S Manual preview
1998 Forester
Бренд: Subaru Страницы: 298
Subaru Legacy 2011 Quick Reference Manual preview
Legacy 2011
Бренд: Subaru Страницы: 19
Safe Fleet PRIME DESIGN HXR-269-E-UM3-80 Manual preview
PRIME DESIGN HXR-269-E-UM3-80
Бренд: Safe Fleet Страницы: 12
Dometic LMC Eriba Nova Service Manual preview
LMC Eriba Nova
Бренд: Dometic Страницы: 24
Ford F-250 Super Duty 2022 Owner'S Manual preview
F-250 Super Duty 2022
Бренд: Ford Страницы: 740
MBRP 0130717 Assembly preview
0130717
Бренд: MBRP Страницы: 5
Edelbrock Honda XR400 Instruction Supplement preview
Honda XR400
Бренд: Edelbrock Страницы: 2
Hudson Super Six 1916 Reference Book preview
Super Six 1916
Бренд: Hudson Страницы: 77
Subaru 1999 Legacy Owner'S Manual preview
1999 Legacy
Бренд: Subaru Страницы: 399
Thermo King V-520 RT Series Installation Manual preview
V-520 RT Series
Бренд: Thermo King Страницы: 56

Бренды по названию

Популярные бренды

Загрузить еще бренды