manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1D-9 Engine Mechanical: 

Air Cleaner Element Inspection and Cleaning

S4RS0A1406002

Inspection

Check air cleaner element for dirt. Replace excessive 
dirty element.

Cleaning

Blow off dust by compressed air from air outlet side of 
element.

Cylinder Head Cover Removal and Installation

S4RS0A1406011

Removal

1) Disconnect negative cable at battery.
2) Disconnect MAF sensor coupler (1).
3) Remove EVAP canister purge valve (2).
4) Remove air cleaner case (3) and resonator (4).
5) Remove cylinder head upper cover (5).

6) Disconnect ignition coil couplers (1).
7) Remove ignition coil assemblies (2) with high-

tension cord (3).

8) Remove wire harness clamp (4) from cylinder head 

cover.

9) Remove oil level gauge (1).

10) Disconnect PCV hose (2) from PCV valve (3) and 

disconnect breather hose (4) from cylinder head 
cover.

11) Remove cylinder head cover mounting bolts in such 

order as indicated in the figure.

12) Remove cylinder head cover (1) with cylinder head 

cover gasket (2) and spark plug hole gasket (3).

Installation

1) Install new spark plug hole gaskets (1) and new 

cylinder head cover gasket (2) to cylinder head cover 
(3) as shown in the figure.

I2RH0B140150-

4

5

3

1

2

I3RM0A140008-

I2RH0B140032-

I2RH0B140033-

I2RH0B140034-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Kathrein DDA Series User Manual preview
DDA Series
Бренд: Kathrein Страницы: 7
Aries P35-2004 Installation Manual preview
P35-2004
Бренд: Aries Страницы: 3
Calix M5T 187A Assembly Instructions preview
M5T 187A
Бренд: Calix Страницы: 5
Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Бренд: Mazda Страницы: 12
Harman Kardon DP 2US Quick Start Manual preview
DP 2US
Бренд: Harman Kardon Страницы: 16
TATA Motors TIAGO XZ 2019 Owner'S Manual preview
TIAGO XZ 2019
Бренд: TATA Motors Страницы: 184
B&G electronics PW-50C Civilian Installation And Operation Manual preview
PW-50C Civilian
Бренд: B&G electronics Страницы: 7
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Бренд: Dakota Digital Страницы: 3
tams elektronik FCS-4 Manual preview
FCS-4
Бренд: tams elektronik Страницы: 19
Hyundai Santa Fe 2019 Getting Started Manual preview
Santa Fe 2019
Бренд: Hyundai Страницы: 18
KEKO K162 Installation Instructions Manual preview
K162
Бренд: KEKO Страницы: 13
Road Armor Stealth 4191F Series Install Instructions preview
Stealth 4191F Series
Бренд: Road Armor Страницы: 5
Linear Logic scangauge2 Quick Start Manual preview
scangauge2
Бренд: Linear Logic Страницы: 8
Mercedes-Benz Vito Taxi 2011 Operation Manual preview
Vito Taxi 2011
Бренд: Mercedes-Benz Страницы: 10
TomTom LINK 105 Installation Manual preview
LINK 105
Бренд: TomTom Страницы: 22
CARFACE CF145962E Instruction Manual preview
CF145962E
Бренд: CARFACE Страницы: 16
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Бренд: RAM Страницы: 360
ADAPT SOLUTIONS ASENTO EV-COLC15R Installation Manual preview
ASENTO EV-COLC15R
Бренд: ADAPT SOLUTIONS Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды