manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Body Electrical Control System:  10B-1

Body Electrical Control System

 

Precautions

Precautions in Diagnosing Trouble

S4RS0AA200001

• Diagnostic information stored in BCM memory can be cleared as well as checked by using SUZUKI scan tool. 

Before using scan tool, read its Operator’s (Instruction) Manual carefully to have good understanding as to what 
functions are available and how to use it.

• Be sure to read “Precautions for Electrical Circuit Service:  in Section 00” before inspection and observe what is 

written there.

• Communication of ECM, TCM (if equipped), combination meter and BCM, is established by CAN (Controller Area 

Network). Therefore, handle CAN communication line with care referring to “Precaution for CAN Communication 
System:  in Section 00”.

General Description

BCM General Description

S4RS0AA201001

The Body electrical Control Module (BCM) is incorporated in junction block assembly. Do not attempt removal of BCM 
from junction block assembly as it may cause contact failure.
The BCM incorporates relays and controllers which are used for the following systems and controls them.
• Power door lock
• Keyless entry
• Rear wiper
• Combination meter
• Interior light
• Warning buzzer
• Rear end door window defogger
• Rear end door opener
• Alarm indicator lamp
Also, the BCM has a function to cause the interior light and open door warning lamp in the combination meter to turn 
off when any door is left open for longer than 15 minutes to reduce wasteful battery consumption.
In addition, it is possible to check operation of actuator which is controlled by BCM by using the output test function of 
SUZUKI scan tool to operate actuator simulatively.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

KC HiLiTES C Series Wiring Diagram preview
C Series
Бренд: KC HiLiTES Страницы: 4
AC Schnitzer F40 Fitting Instructions Manual preview
F40
Бренд: AC Schnitzer Страницы: 16
Eclipse AVN 2210p mkII Operation Manual preview
AVN 2210p mkII
Бренд: Eclipse Страницы: 6
Yakima RoadShower 10G Quick Start Manual preview
RoadShower 10G
Бренд: Yakima Страницы: 12
Hama 00178266 Operating Instruction preview
00178266
Бренд: Hama Страницы: 75
Tachosys digidl Installation Manual preview
digidl
Бренд: Tachosys Страницы: 28
TOPPOINT LT95090 Quick Start Manual preview
LT95090
Бренд: TOPPOINT Страницы: 2
TracRac TracONE Installation Instructions Manual preview
TracONE
Бренд: TracRac Страницы: 8
Safe Fleet PRIME DESIGN HRR3-E-PM52 Manual preview
PRIME DESIGN HRR3-E-PM52
Бренд: Safe Fleet Страницы: 12
GROM Audio VLINE Installation Manual preview
VLINE
Бренд: GROM Audio Страницы: 20
Metra Electronics 99-3305 Installation Instructions Manual preview
99-3305
Бренд: Metra Electronics Страницы: 12
DICE DCR-150 Installation Manual preview
DCR-150
Бренд: DICE Страницы: 1
Hudson Super-Six 1926 Instruction Book preview
Super-Six 1926
Бренд: Hudson Страницы: 24
Magneti Marelli BCF636 Installation Instruction preview
BCF636
Бренд: Magneti Marelli Страницы: 2
Axxess AXDSPX-TY3 Installation Instructions Manual preview
AXDSPX-TY3
Бренд: Axxess Страницы: 16
Prorack K129 Fitting Instructions Manual preview
K129
Бренд: Prorack Страницы: 13
Skyjacker TRU25 Installation Instructions preview
TRU25
Бренд: Skyjacker Страницы: 2
PROUSER MCH6A Manual preview
MCH6A
Бренд: PROUSER Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды