manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Lighting Systems:  9B-10

3) Check turn R circuit

Connect terminal “6” and battery negative (–) 
terminal by a jumper wire.
Check right side bulbs (1) for flashing cycle.
If check result is not as specified, replace turn signal 
and hazard warning relay.

Reference flashing cycle
60 – 120 cycle/minute

4) Check Hazard ON circuit

Connect terminal “8” and battery negative (–) 
terminal by a jumper wire.
Check all bulbs (1) for flashing cycle.
If check result is not as specified, replace turn signal 
and hazard warning relay.

Reference flashing cycle
60 – 120 cycle/minute

License Lamp Assembly Removal and 
Installation

S4RS0A9206022

Removal

1) Disconnect negative (–) cable at battery.
2) Remove rear bumper. Refer to “Front Bumper and 

Rear Bumper Components:  in Section 9K”

3) Disconnect coupler (1) from license lamp assembly 

(2).

4) Push locking part to arrow direction, and then 

remove license lamp assembly (2).

Installation

Reverse removal procedure for installation.

Front Fog Light Assembly Removal and 
Installation

S4RS0A9206016

Removal

1) Disconnect negative (–) cable at battery.
2) Remove front bumper. Refer to “Front Bumper and 

Rear Bumper Components:  in Section 9K”.

3) Disconnect couplers (1) from fog light (2).
4) Remove fog light screws (3), and remove front fog 

light assembly (2).

Installation

Reverse removal procedure for installation nothing the 
following:
• After installing, adjust aiming referring to “Front Fog 

Light Aiming Adjustment with Screen: ”.

3

8

7

1

2

6

5 4

1

I4RS0A920016-

3

8

7

1

2

6

5 4

1

1

I4RS0A920017-

2

2

1

2

I4RS0A920018-

3

3

1

2

I4RS0A920019-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Fass Titanium Series Installation Manual preview
Titanium Series
Бренд: Fass Страницы: 13
Feniex AM600 Instruction Manual preview
AM600
Бренд: Feniex Страницы: 6
IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Бренд: IAME Страницы: 17
Havis-Shields 1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28 Install Instructions preview
1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28
Бренд: Havis-Shields Страницы: 3
Safe Fleet RVS-082550 Instruction Manual preview
RVS-082550
Бренд: Safe Fleet Страницы: 11
Camec 042374 User Manual preview
042374
Бренд: Camec Страницы: 19
AC Schnitzer X3 M-Technik Fitting Instructions Manual preview
X3 M-Technik
Бренд: AC Schnitzer Страницы: 20
Alfa Romeo Alfa 147 Quick Start Manual preview
Alfa 147
Бренд: Alfa Romeo Страницы: 8
Saab 12 787 887 Installation Instructions Manual preview
12 787 887
Бренд: Saab Страницы: 12
Jeep Cherokee 1977 Owner'S Manual preview
Cherokee 1977
Бренд: Jeep Страницы: 136
Volvo 164 1969 Service Manual preview
164 1969
Бренд: Volvo Страницы: 266
Vauxhall Meriva 2014 Infotainment Manual preview
Meriva 2014
Бренд: Vauxhall Страницы: 131
TATA Motors INDICA eV2 XETA CNG Supplemental Owner'S Manual preview
INDICA eV2 XETA CNG
Бренд: TATA Motors Страницы: 24
PAC AP4-GM61 Quick Start Manual preview
AP4-GM61
Бренд: PAC Страницы: 5
Percon Falcon 655 User Manual preview
Falcon 655
Бренд: Percon Страницы: 49
Havis-Shields Telescoping Computer Base C-TCB-34 Install Instructions preview
Telescoping Computer Base C-TCB-34
Бренд: Havis-Shields Страницы: 1
PEUGEOT 106 2001 Owner'S Manual preview
106 2001
Бренд: PEUGEOT Страницы: 107
Mitsubishi 2015 OUTLANDER Owner'S Manual preview
2015 OUTLANDER
Бренд: Mitsubishi Страницы: 490

Бренды по названию

Популярные бренды

Загрузить еще бренды