Suzuki RM-Z450 Скачать руководство пользователя страница 65

Страница: 65 / 121

6-6

ENGINE RUN TIME INDICATION
PROCEDURE

1. Disconnect the battery coupler

from the cap.

2. Connect a 12 volt battery to

the battery coupler using the
battery wire.



36890-28H00:
Battery wire (option)

3. After indicator light will be lit for

2 seconds (lamp check),
engine run time will be dis-
played by indicator light light-
ing time.

NOTE:
•

Lighting of lamp check and
engine run time is made only
at the first time, and when
there is DTC available, this
DTC will be displayed repeat-
edly.

•

Indicator light will be lit for 0.2
sec. per 1 hour of engine run
time.

•

However, the display of engine
run time is limited to 100 hours
(lit for 20 sec.).

•

Perform the same operation
when starting the engine.

Содержание RM-Z450


























































































































Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды

Suzuki RM-Z450, Руководство пользователя

Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды