Suzuki RM-Z450 Скачать руководство пользователя страница 53

Страница: 53 / 121

5-8

SELECTING A MODE

Start the engine and shift the gear to neutral, 1st, or 2nd. Next, adjust
the engine speed so it is no greater than 3500 rpm.

NOTE: The S-HAC mode setting cannot be change (to mode-A or
mode-B) while a DTC (Diagnostic Trouble Code) is displayed.

Mode-A

•

The indicator light

will light for a lamp check (2 seconds) and

then become an engine run time indicator light. Note, however, that
even while the indicator light is lit to indicate the engine run time,
holding down the S-HAC switch

for more than 0.7 seconds will

cause the indicator light

to switch to slow flashing (mode-A).

•

To select mode-A, release the S-HAC switch

while the indicator

light

is flashing slowly (for about 1.8 seconds).

•

Selecting mode-A will cause the slow flash pattern to continue.

NOTE:
•

To switch to the normal mode from mode-A, hold down the S-HAC
switch until the indicator light

goes out.

•

To switch from mode-A to mode-B, first switch to the normal mode
and then switch to mode-B.

Содержание RM-Z450


























































































































Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды

Suzuki RM-Z450, Руководство пользователя

Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды