Suzuki RM-Z450 Скачать руководство пользователя страница 108

Страница: 108 / 121

7-5

MOTORCYCLE CLEANING

Follow the instructions below to
prevent water from entering the
engine through the air cleaner
element when cleaning the motor-
cycle.

•

Cover the element with a plas-
tic bag.

•

Install the seat.

•

Cover the inlet holes on the
frame covers in order to pre-
vent water from entering the
air cleaner box.

•

Do not spray high pressure
water to the air cleaner box.

Washing the Motorcycle

When washing the motorcycle,
follow the instructions below:
1. Remove dirt and mud from the

motorcycle with cool running
water. You may use a soft
sponge or brush. Do not use
hard materials which can
scratch the paint.

2. Wash the entire motorcycle

with a mild detergent or car
wash soap using a sponge or
soft cloth. The sponge or cloth
should be frequently soaked in
the soap solution.

NOTE: Avoid spraying or allowing
water to flow over the following
places:
•

Spark plug

•

Fuel tank cap

•

Fuel injection system

•

Brake master cylinders

•

Throttle cable boots

Содержание RM-Z450


























































































































Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды

Suzuki RM-Z450, Руководство пользователя

Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды