Suzuki RM-Z450 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 121

background image

7-3

PROCEDURE FOR RETURNING
TO SERVICE

1. Clean the entire motorcycle.
2. Remove the oily rags from the

air cleaner intake and muffler
outlet.

3. Drain all the engine oil. Install

a new oil filter and fill the
engine with fresh oil as out-
lined in this manual.

4. Remove the spark plug. Turn

the engine a few times. Rein-
stall the spark plug.

5. Make sure that the motorcycle

is properly lubricated.

6. Perform the INSPECTION

BEFORE RIDING as listed in
this manual.

7. Start the motorcycle as out-

lined in this manual.

If the engine is hard to start, follow
the procedure below:

Due to deterioration of fuel
remaining in the fuel line for long
period, engine will be difficult to
start until the deteriorated (stale)
fuel is discharged from the fuel
line. Repeated kick operation is
required for flushing the fuel line
with fresh fuel.

1. Fill the fuel tank more than half

full.

2. Shift the transmission into neu-

tral.

3. While keeping the throttle

approximately 1/4 open,
repeat kick start operation 30
to 40 times.

NOTE: Fuel injection volume is
controlled to increase in throttle
open condition. However, do not
open throttle more than 1/2 as
fuel injection is shut off in wide
open throttle in engine start
mode.

4. Start the engine by following

cold engine start procedure.

NOTE: If the engine fails to start
after several attempts, spark plug
will be get wet. In this case,
repeat kick start operation 4 to 5
times with throttle fully opened to
dry the spark plug. No fuel is
injected with full throttle opening
in engine start mode.

«
...
104
105
106
107
108
...
»

Содержание RM-Z450


























































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z450

Бренд: S&B Filters Страницы: 7

Бренд: Öhlins Страницы: 2

Mechatronics 35007-01

Бренд: Öhlins Страницы: 4

McPherson Strut MIR 5H02

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 4

Бренд: Dennis Kirk Страницы: 5

Бренд: R&G Страницы: 24

Бренд: kellermann Страницы: 7

Бренд: ESAB Страницы: 4

Бренд: LSL Страницы: 4

BRUTALE 750 ORO

Бренд: MV Agusta Страницы: 386

Бренд: DYNATEK Страницы: 4

Бренд: VESPA Страницы: 64

Бренд: SAFARI Страницы: 18

Бренд: IL Motorsport Страницы: 2

Бренд: Benelli Страницы: 55

Бренд: Benelli Страницы: 65

Бренд: Benelli Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды