Suzuki RM-Z450 Скачать руководство пользователя страница 100

Страница: 100 / 121

6-41

SPOKE NIPPLE AND
BEAD STOPPER NUT

Check the tension to verify the
tightness of the spoke nipples.
The tension of the spokes can be
checked by squeezing the spokes
with your fingers. If a spoke nipple
is loose, the spoke will bend more
than the others.

Retighten the spoke nipples with
a spoke nipple wrench so as all
spokes have same tension.



Spoke nipple (front wheel):
5.5 N·m (0.56 kgf-m, 4.05 lbf-ft)



Spoke nipple (rear wheel):
6.0 N·m (0.61 kgf-m, 4.45 lbf-ft)

Inspect the bead stopper nut

for tightness.



Bead stopper nut
(front and rear wheel):
14 N·m (1.4 kgf-m, 10.5 lbf-ft)

NOTICE

Improperly tightening the
spoke nipples can damage the
wheel.

Tighten the spoke nipples less
than 1/2 turn at a time. Inspect
the spoke tension and then
retighten the spoke nipple.

Содержание RM-Z450


























































































































Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды

Suzuki RM-Z450, Руководство пользователя

Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды