Suzuki RM-Z250 Скачать руководство пользователя страница 245

Страница: 245 / 411

12-62 FI SYSTEM DIAGNOSIS

ECT SENSOR INSPECTION

The ECT sensor

is installed on the cylinder head.

• Remove the ECT sensor. (



below)

• Check the ECT sensor by testing it at the bench as shown in

the figure. Connect the ECT sensor

to a circuit tester and

place it in the oil

contained in a pan, which is placed on a

stove.

• Heat the oil to raise its temperature slowly and read the col-

umn thermometer

and the ohmmeter.

• If the ECT sensor ohmic value does not change in the propor-

tion indicated, replace it with a new one.



ECT sensor specification



09900-25008: Multi-circuit tester set



Tester knob indication: Resistance (

Ω

)



ECT SENSOR REMOVAL AND INSTALLATION

• Drain engine coolant. (



14-3)

• Disconnect the ECT sensor coupler

• Remove the ECT sensor

Engine Coolant Temp.

Resistance

20 °C (68 °F)

Approx. 2.58 k

Ω

50 °C (122 °F)

Approx. 0.77 k

Ω

80 °C (176 °F)

Approx. 0.28 k

Ω

110 °C (230 °F)

Approx. 0.12 k

Ω

* Take special care when handling the ECT sensor. It

may cause damage if it gets a sharp impact.

* Do not contact the ECT sensor and the column ther-

mometer with a pan.

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды

Suzuki RM-Z250, Руководство по обслуживанию

Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды