manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

3) If equipped with passenger air bag (inflator) module, connect

Yellow connector (1) of passenger air bag (inflator) module, and
be sure to lock connector with lock lever.
a) Connect connector.
b) Lock connector with lock lever.

4) Install glove box.
5) Install “AIR BAG” fuse to fuse box.
6) Turn ignition switch to ON position and verify that “AIR BAG”

warning lamp flashes 6 times and then turns OFF.
If it does not operate as described, perform AIR BAG DIAG-
NOSTIC SYSTEM CHECK in this section.

a)

b)

a)

1

HANDLING AND STORAGE

SDM

WARNING:
Never power up air bag system when SDM is not rigidly
attached to the vehicle. Otherwise, personal injury may
result.

CAUTION:
After detecting one time of such collision as to meet de-
ployment conditions, the SDM must not be used.
Refer to AIR BAG DIAGNOSTIC SYSTEM CHECK when
checking the SDM.

Never attempt disassembly of SDM.

When storing SDM, select a place where neither high tempera-
ture nor high humidity is anticipated and oil, water and dust are
kept off.

If SDM has been dropped, replace it with a new one.

If installation part of SDM was damaged, repair that part com-
pletely before reinstallation.

All SDM and mounting bracket fasteners must be carefully
torqued and the arrow must be pointed toward the front of the
vehicle to ensure proper operation of the air bag system.

10B-46

AIR BAG SYSTEM

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Saab 99 Important Operatlng, Safety And Maintenance Instructions preview
99
Бренд: Saab Страницы: 75
N-Com B3 User Instructions And Safety preview
B3
Бренд: N-Com Страницы: 28
Baja Designs S8 Instructions Manual preview
S8
Бренд: Baja Designs Страницы: 6
Jeep Compass Overview Manual preview
Compass
Бренд: Jeep Страницы: 25
Carefree Slideout Cover Service Manual preview
Slideout Cover
Бренд: Carefree Страницы: 12
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Бренд: GOgroove Страницы: 9
Roav R5141 Owner'S Manual preview
R5141
Бренд: Roav Страницы: 10
Globalsat MR-350P Installation Manual preview
MR-350P
Бренд: Globalsat Страницы: 2
STC 552-010 Installation Instructions Manual preview
552-010
Бренд: STC Страницы: 6
SuperATV Roof Installation Instructions Manual preview
Roof
Бренд: SuperATV Страницы: 7
Whelen Engineering Company FastTrax FTF4 Installation Manual preview
FastTrax FTF4
Бренд: Whelen Engineering Company Страницы: 9
T-Mobile SyncUP DRIVE Start Manual preview
SyncUP DRIVE
Бренд: T-Mobile Страницы: 2
Westin 31-0190 Installation Instructions preview
31-0190
Бренд: Westin Страницы: 2
NavInc CP-PEU-GV3 Manual preview
CP-PEU-GV3
Бренд: NavInc Страницы: 6
E&G Classics Denali 1094-0185-15 Instruction Manual preview
Denali 1094-0185-15
Бренд: E&G Classics Страницы: 3
Metra Electronics 99-7803G Wiring Instructions preview
99-7803G
Бренд: Metra Electronics Страницы: 2
Alphasonik PCP15LDE Owner'S Manual preview
PCP15LDE
Бренд: Alphasonik Страницы: 8
Safe Fleet PRIME DESIGN VRR3-FT21G-ST Manual preview
PRIME DESIGN VRR3-FT21G-ST
Бренд: Safe Fleet Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды