Suzuki Intruder VZR1800 Скачать руководство пользователя страница 528 | Manualshive

Страница: 528 / 586

background image

EMISSION CONTROL INFORMATION 12-5

NOISE EMISSION CONTROL SYSTEM

TAMPERING WITH THE NOISE CONTROL SYSTEM PROHIBITED: Local law prohibits the following acts
or the causing thereof:
1. The removal or rendering inoperative by any person, other than for purposes of maintenance, repair or

replacement, of any device or element of design incorporated into any new vehicle for the purpose of
noise control prior to its sale or delivery to the ultimate purchaser or while it is in use, or

2. The use of the vehicle after such device or element of design has been removed or rendered inoperative

by any person.

AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW:

• Removing or puncturing the muffler, baffles, header pipes, screen type spark arrester (if equipped) or any

other component which conducts exhaust gases.

• Removing or puncturing the air cleaner case, air cleaner cover, baffles or any other component which

conducts intake air.

• Replacing the exhaust system or muffler with a system or muffler not marked with the same model spe-

cific code as the code listed on the Motorcycle Noise Emission Control Information label.

«
...
526
527
528
529
530
...
»

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intruder VZR1800

Бренд: S&B Filters Страницы: 7

Бренд: Dynojet Страницы: 2

Бренд: KDX Страницы: 7

Бренд: Memphis Shades Страницы: 2

Бренд: Honda Страницы: 28

MD-052-2 Series

Бренд: Acewell Страницы: 2

D14/4 BANTAM SUPREME D14/4 BANTAM SPORTS

Бренд: BSA Страницы: 120

Two Fifty 250 cc

Бренд: Mash Страницы: 62

Бренд: HERO Страницы: 68

Бренд: AGV Страницы: 64

Бренд: Yamaha Страницы: 172

Бренд: Yamaha Страницы: 80

Бренд: hepco & becker Страницы: 4

Бренд: SHERCO Страницы: 54

Бренд: VOR Motori Страницы: 100

Бренд: Aosom Страницы: 13

Бренд: Legend Страницы: 2

TORNADO Tre Novecento 900

Бренд: Benelli Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды