manualshive.com logo in svg

Suzuki Intruder VZR1800, Руководство по обслуживанию


Поделиться
Скачать
background image

ELECTRICAL SYSTEM     10-9

Step 5

1) Measure the generator no-load performance. (

!

10-11)

Is the generator no-load performance OK?

Step 6

1) Inspect the regulator/rectifier. (

!

10-11)

Is the regulator/rectifier OK?

Step 7

1) Inspect wirings.

Is the wirings OK?

Battery overcharges

• Faulty regulator/rectifier
• Faulty battery
• Poor contact of generator lead wire coupler

INSPECTION

BATTERY CURRENT LEAKAGE

• Remove the front seat. (

!

9-4)

• Turn the ignition switch to the OFF position.
• Remove the battery cover.
• Disconnect the battery 

 

-

 lead wire.

• Measure the current between 

 

-

 battery terminal and the 

 

-

battery lead wire using the multi-circuit tester. If the reading
exceeds the specified value, leakage is evident.

"

09900-25008: Multi-circuit tester set

$

Battery current (leak): Under 3 mA

%

Tester knob indication: Current (

&

, 20 mA)

#

YES

Go to Step 6.

NO

Faulty generator

YES

Go to Step 7.

NO

Faulty regulator/rectifier

YES

Faulty battery

NO

• Short circuit of wire harness
• Poor contact of couplers

* In case of a large current leak, turn the tester to high

range first to avoid tester damage.

* Do not turn the ignition switch to the “ON” position

when measuring current.

A

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intruder VZR1800

LAZER Century User Manual preview
Century
Бренд: LAZER Страницы: 6
Happy Trails HTP1-12-7 Quick Start Manual preview
HTP1-12-7
Бренд: Happy Trails Страницы: 3
Ops-Core Mesh Helmet Cover Installation preview
Mesh Helmet Cover
Бренд: Ops-Core Страницы: 2
Yoshimura 070BG141503 Quick Start Manual preview
070BG141503
Бренд: Yoshimura Страницы: 3
Sharper Image 206949 User Manual preview
206949
Бренд: Sharper Image Страницы: 4
Nolan N-Com B101 Manual preview
N-Com B101
Бренд: Nolan Страницы: 24
KYMCO PEOPLE S 125 Owner'S Manual preview
PEOPLE S 125
Бренд: KYMCO Страницы: 55
Yoshimura RACE 13100CP520 Manual preview
RACE 13100CP520
Бренд: Yoshimura Страницы: 7
Paaschburg & Wunderlich HIGHSIDER VICTORY Mounting And Safety Instructions preview
HIGHSIDER VICTORY
Бренд: Paaschburg & Wunderlich Страницы: 5
Suzuki 2001 GSX1300RK1 HAYABUSA Supplementary Service Manual preview
2001 GSX1300RK1 HAYABUSA
Бренд: Suzuki Страницы: 31
National Cycle ZTechnik VStream Z2392 Installation Instructions preview
ZTechnik VStream Z2392
Бренд: National Cycle Страницы: 2
Honda XL125LK Owner'S Manual preview
XL125LK
Бренд: Honda Страницы: 243
Honda 2009 crf 450r Service Manual preview
2009 crf 450r
Бренд: Honda Страницы: 556
DYNATEK D3K1-4 Installation Instructions preview
D3K1-4
Бренд: DYNATEK Страницы: 3
DYNATEK D2K-HD1 User Instructions preview
D2K-HD1
Бренд: DYNATEK Страницы: 8
Shark SHKC7800N User Manual preview
SHKC7800N
Бренд: Shark Страницы: 16
MINIMOTO Sport Racer Instruction Manual preview
Sport Racer
Бренд: MINIMOTO Страницы: 20
Yamaha V-Star XVS250S Owner'S Manual preview
V-Star XVS250S
Бренд: Yamaha Страницы: 82

Бренды по названию

Популярные бренды

Загрузить еще бренды