manualshive.com logo in svg

Suzuki Intruder VZR1800, Руководство по обслуживанию


Поделиться
Скачать
background image

COOLING AND LUBRICATION SYSTEM     8-9

ECT SENSOR

REMOVAL

• Drain the engine coolant. (

#

2-20)

• Remove the air cleaner chamber and throttle body. (

#

6-13)

• Disconnect the ECT sensor coupler 

 

1

.

• Remove the rear intake pipe and thermostat assembly.

(

#

3-13)

• Remove the ECT sensor 

 

2

.

INSPECTION

• Check the ECT sensor by testing it at the bench as shown in

the figure. Connect the ECT sensor 

 

1

 to a circuit tester and

place it in the oil 

 

2

 contained in a pan, which is placed on a

stove.

• Heat the oil to raise its temperature slowly and read the col-

umn thermometer 

 

3

 and the ohmmeter.

• If the ECT sensor ohmic value does not change in the propor-

tion indicated, replace it with a new one.

$

Temperature sensor specification

$

Cooling fan operating temperature:
Standard (OFF

→

ON): Approx. 105 °C (221 °F)

(ON

→

OFF): Approx. 100 °C (212 °F)

NOTE:
As coolant temperature rises, the cooling fan operates for 5 sec-
onds when the temperature arrives each at 50

 – 

70 °C (122 –

158 °F), 70

 – 

90 °C (158

 – 

194 °F) and 90

 – 

110 °C (194

  –

230 °F)/above 4 000 r/min.

Temperature

Standard resistance

20 °C (68 °F)

Approx. 2.45 k

Ω

50 °C (122 °F)

Approx. 0.811 k

Ω

80 °C (176 °F)

Approx. 0.318 k

Ω

110 °C (230 °F)

Approx. 0.142 k

Ω

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intruder VZR1800

Yamaha FZ6-SS Service Manual preview
FZ6-SS
Бренд: Yamaha Страницы: 435
Baja motorsports DR50 Assembly Manual preview
DR50
Бренд: Baja motorsports Страницы: 20
Yamaha YZFR1A Owner'S Manual preview
YZFR1A
Бренд: Yamaha Страницы: 124
N-Com SPCOM00000032 Instructions preview
SPCOM00000032
Бренд: N-Com Страницы: 2
KTM 50 SX 2015 Setup Instructions preview
50 SX 2015
Бренд: KTM Страницы: 13
Insportline W-TEC AP-42 User Manual preview
W-TEC AP-42
Бренд: Insportline Страницы: 19
Crivit 303613 Instructions For Use Manual preview
303613
Бренд: Crivit Страницы: 58
Dakota Digital MLX-3000 Manual preview
MLX-3000
Бренд: Dakota Digital Страницы: 11
Pacific Helmets HALOFLEX F20H User'S Information Manual preview
HALOFLEX F20H
Бренд: Pacific Helmets Страницы: 40
Aim MXK10 User Manual preview
MXK10
Бренд: Aim Страницы: 47
SpeedAngle GMOS JI100S User Manual preview
GMOS JI100S
Бренд: SpeedAngle Страницы: 37
hepco & becker 6302513 00 01 Manual preview
6302513 00 01
Бренд: hepco & becker Страницы: 3
Race Dynamics PowerTRONIC Installation Manual preview
PowerTRONIC
Бренд: Race Dynamics Страницы: 25
Yamaha BWS CW50L Owner'S Manual preview
BWS CW50L
Бренд: Yamaha Страницы: 68
Petzl BOREO Manual preview
BOREO
Бренд: Petzl Страницы: 4
KTM 90.06.019.000 Mounting Instructions preview
90.06.019.000
Бренд: KTM Страницы: 2
KTM Power Parts Information preview
Power Parts
Бренд: KTM Страницы: 3
Mastech SUZUKI V-STROM 650 04-UP Quick Start Manual preview
SUZUKI V-STROM 650 04-UP
Бренд: Mastech Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды