Suzuki Intruder VZ1500, Руководство по обслуживанию

Страница: 273 / 580

Engine Mechanical: 1D-84
Tightening Torque Specifications
B940H21407002
NOTE
The specified tightening torque is described in the following.
“Throttle Cable Routing Diagram (Page 1D-2)”
“Throttle Body Components (Page 1D-9)”
“Engine Assembly Installation (Page 1D-24)”
Reference:
For the tightening torque of fastener not specified in this section, refer to “Tightening Torque List in Section 0C
(Page 0C-8)”.
Fastening part
Tightening torque
Note
N
⋅
m kgf-m lbf-ft
Air cleaner box mounting bolt 5.5 0.55 4.0
)
(Page 1D-7)
ISC valve mounting bolt 4.5 0.45 3.0
)
(Page 1D-12)
STP sensor mounting screw 3.5 0.35 2.5
)
(Page 1D-15)
TP sensor mounting screw 3.5 0.35 2.5
)
(Page 1D-16)
Fuel delivery pipe mounting screw 5 0.5 3.5
)
(Page 1D-17)
Frame down tube bolt 50 5.0 36.0
)
(Page 1D-25)
Front footrest bracket bolt 50 5.0 36
)
(Page 1D-26)
Radiator heat shield mounting bolt (Left side) 5.5 0.55 4.0
)
(Page 1D-26)
Radiator heat shield mounting bolt (Right side) 10 1.0 7.0
)
(Page 1D-26)
Cylinder head bolt (L190) (Initial) 25 2.5 18.0
)
(Page 1D-34)
Cylinder head bolt (L190) (Final) 42 4.2 30.5
)
(Page 1D-34)
Cylinder head bolt (L180) 26 2.6 19.0
)
(Page 1D-34)
Cylinder head bolt (L160) 26 2.6 19.0
)
(Page 1D-34)
Cam chain sprocket bolt 15 1.5 11.5
)
(Page 1D-36)
Camshaft journal holder bolt
10 1.0 7.0
)
(Page 1D-37) /
)
(Page 1D-38) /
)
(Page 1D-42)
Cam chain tension adjuster bolt
10 1.0 7.0
)
(Page 1D-38) /
)
(Page 1D-39)
Cam chain tension adjuster cap bolt
23 2.3 16.5
)
(Page 1D-38) /
)
(Page 1D-39)
Cylinder head cover bolt 14 1.4 10.0
)
(Page 1D-40)
Valve timing inspection cap bolt 10 1.0 7.0
)
(Page 1D-44)
Cylinder head cover bracket bolt 10 1.0 7.0
)
(Page 1D-45)
Water jacket plug (Cylinder head) 26 2.6 19.0
)
(Page 1D-47)
Oil gallery plug (M16) 35 3.5 25.5
)
(Page 1D-64)
Oil gallery plug (M14) 23 2.3 16.5
)
(Page 1D-64)
Oil gallery plug (M8) 18 1.8 13.0
)
(Page 1D-64)
Oil gallery plug (Transmission oil jet) (M10) 18 1.8 13.0
)
(Page 1D-64)
Crankcase bolt (M6) 11 1.1 8.0
)
(Page 1D-67)
Crankcase bolt (M8) (Initial) 15 1.5 11.0
) (Page 1D-67)
Crankcase bolt (M8) (Final)
26 2.6 19.0
)
(Page 1D-67)
Oil pressure switch 14 1.4 10
)
(Page 1D-67)
Gearshift arm stopper 19 1.9 13.5
)
(Page 1D-69)
Gearshift cam stopper bolt 10 1.0 7.0
)
(Page 1D-69)
Gearshift cam stopper plate bolt 10 1.0 7.0
)
(Page 1D-69)
Cam chain guide bolt
23 2.3 16.5
)
(Page 1D-70) /
)
(Page 1D-71)
Rear cam chain tensioner bolt 23 2.3 16.5
)
(Page 1D-70)
Secondary drive gear bolt 160 16.0 115.5
)
(Page 1D-71)
Front cam chain tensioner bolt 23 2.3 16.5
)
(Page 1D-71)
Starter motor mounting bolt 10 1.0 7.0
)
(Page 1D-73)
Conrod cap bolt 35 N
⋅
m (3.5 kgf-m, 25.5 Ib-ft) then turn in 1/
4 (90
°
) turn
)
(Page 1D-75) /
)
(Page 1D-76)
Special tool bolt 23 2.3 16.5
)
(Page 1D-79)
Primary drive gear bolt 150 15.0 108.5
)
(Page 1D-81)