manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission/Transaxle:  5A-24

DTC P1777: TCM Lost Communication with ECM (Reception Error)

S5JB0E5104042

Wiring Diagram
Refer to “DTC P1774: CAN Communication Bus Off: ”.

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

1) Connect scan tool to DLC with ignition switch turned OFF.

2) Turn ON ignition switch and clear DTC by using scan tool.

3) Start engine and run it for 1 min. or more.

4) Check DTC and pending DTC.

4

DTC check

1) Turn ignition switch to OFF position.

2) Connect connectors of disconnected control modules 

communicating by means of CAN.

3) Disconnect connector of any one of control module other 

than TCM.

4) Recheck DTC for TCM.

Is DTC P1774 detected?

Disconnect connectors 
of control modules other 
than the one whose 
connector is 
disconnected in Step 3) 
one by one and check 
that DTC P1774 is 
detected by TCM each 
time connector is 
disconnected. When 
DTC P1774 is not 
detected by TCM while 
checking in this way, go 
to description under 
“NO” below. If DTC 
P1774 is detected by 
TCM even when 
connectors of all control 
modules that use CAN 
communication with 
TCM are disconnected, 
substitute a known-
good TCM and recheck.

Check power and 
ground circuit of control 
module disconnected in 
Step3). If circuit is OK, 
substitute a known-
good control module 
disconnected in Step 3) 
and recheck.

Step

Action

Yes

No

DTC Detecting Condition

Trouble Area

Reception error of communication data for ECM is detected for 
longer than specified time continuously.
(1 driving cycle detection logic)

• ECM

• ABS/ESP

®

 control module

• TCM

• CAN communication line circuit

Содержание GRAND VITARA JB416



























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA JB416

Kargo Master 40020 Assembly Manual preview
40020
Бренд: Kargo Master Страницы: 6
DAVIS 8126GD User Manual preview
8126GD
Бренд: DAVIS Страницы: 32
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Бренд: Monacor Страницы: 2
Alfa Romeo Alfa 147 Quick Start Manual preview
Alfa 147
Бренд: Alfa Romeo Страницы: 8
Nav TV AUDI A6 Installation Manual preview
AUDI A6
Бренд: Nav TV Страницы: 5
Dodge Ram Commercial2016 Owner'S Manual preview
Ram Commercial2016
Бренд: Dodge Страницы: 675
Audiovox UniStreamONE Installation Manual preview
UniStreamONE
Бренд: Audiovox Страницы: 24
Mercedes-Benz GLE Coupe Brief Overview preview
GLE Coupe
Бренд: Mercedes-Benz Страницы: 2
Westin 25-0560 Instructions preview
25-0560
Бренд: Westin Страницы: 2
Menabo DELTA DL FIX 209FP Fitting Instructions Manual preview
DELTA DL FIX 209FP
Бренд: Menabo Страницы: 8
Alphasonik PCP15LDE Owner'S Manual preview
PCP15LDE
Бренд: Alphasonik Страницы: 8
Cadillac XLR-V Specifications preview
XLR-V
Бренд: Cadillac Страницы: 2
Buick Cascada 2016 Getting To Know Manual preview
Cascada 2016
Бренд: Buick Страницы: 20
Ford TRANSIT CUSTOM Quick Reference Manual preview
TRANSIT CUSTOM
Бренд: Ford Страницы: 15
Honda 08L04-SZA-100 Installation Instructions preview
08L04-SZA-100
Бренд: Honda Страницы: 3
Safe Fleet PRIME DESIGN HRR3-E-PM52 Manual preview
PRIME DESIGN HRR3-E-PM52
Бренд: Safe Fleet Страницы: 12
Bulldog Security BulldogOne BD1 User Manual preview
BulldogOne BD1
Бренд: Bulldog Security Страницы: 7
Axxess AXGMLN-09 Installation Instructions preview
AXGMLN-09
Бренд: Axxess Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды