manualshive.com logo in svg

Suspa VariFrame, Руководство по сборке

Поделиться
Скачать
Suspa VariFrame Скачать руководство пользователя страница 31

 

Installation 

 

VariFrame – Assembly Instructions 

 

page 31 

 

5.3.2.10

 

Installation of the manual switch (exemplary) 

 

Fasten the manual switch (not included in the scope of delivery) in the required 
position on the tabletop. 

 

In doing so, ensure that the connecting cable of the manual switch can be plugged 
into the controller. 

 

Figure 22 Installation of the manual switch 

 

 ATTENTION 

 Use screws with the proper length only. 

Screws that are too long will penetrate the top surface of the tabletop and damage it! 

 WARNING 

 A risk of sustaining injuries due to protruding screws is posed. 

IMPORTANT 

 The manual switch must be fastened in a position that allows it to be connected to the 

controller! 

IMPORTANT 

 The manual switch must always move with the lifting columns on their travel path! 

IMPORTANT 

 Screws to fasten the manual switch to the tabletop are not included in the scope of 

delivery.

 

 

 

 

 

 

Содержание VariFrame








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды