background image

Assembly Process

15

Standard 20lb. tank

 Screw regulator onto gas hose. Do not cross-thread.

Tighten securely.

Install cylinder.

Attach regulator to cylinder.
Complete attachment.

Step 9 - Connect Hose & Regulator to Cylinder

Specifi cations
- You must provide propane gas and propane cylinder. Use a 
   standard 20 lb. Propane cylinder only.
- Use this heater only with a propane vapor withdrawal supply 
   system. See Chapter 5 of the Standard  for Storage and 
   Handling of Liquefi ed Petroleum Gas, ANSI/NFPA 58. Your local 
   library or fi re department should have this book.
- The minimum permissible gas supply pressure of 10 W.C. is 
   required for purpose of input adjustment.
- The installation must conform with local codes, or in absence of 
   local codes, with National Fuel Gas Code, ANSI Z223.1.
- The minimum hourly output of 17000 Btu is the required rating of 
   a heater  operating at ratings less than full input rating.
- The pressure regulator and hose assembly supplied with the 
   appliance must be used.
-  A dented, rusted or damaged propane cylinder may be 
   hazardous and should be checked by your cylinder supplier. 
   Never use a propane cylinder with a damaged valve connection.
- The propane cylinder must be constructed and marked in 
   accordance with the specifi cation for LP gas cylinders of the U.S. 
   Department of Transportation (DOT).
-  Never connect an unregulated propane cylinder to the heater.

Содержание Four Seasons FM87PHLP























Отзывы: