Supermicro SuperServer SYS-2049U-TR4 Скачать руководство пользователя страница 37

Страница: 37 / 151

Chapter 3: Maintenance and Component Installation

4-way Motherboards w/Half Memory Configuration Support

Note:

Unbalanced memory configuration decreases memory performance and is not

recommended for Supermicro motherboards.

Memory Population Table for the 4-way Motherboard w/Half Memory Configuration

Support ( w/4 CPUs & 24 DIMMs Installed)

4 CPUs & 24 DIMMs

(6 DIMMs per CPU)

Memory Population Sequence

CPU1 + 6 DIMMs

CPU1: P1-DIMMC1/P1-DIMMB1/P1-DIMMA1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1

CPU2 + 6 DIMMs

CPU2: P2-DIMMC1/P2-DIMMB1/P2-DIMMA1/P2-DIMMD1/P2-DIMME1/P2-DIMMF1

CPU3 + 6 DIMMs

CPU3: P3-DIMMC1/P3-DIMMB1/P3-DIMMA1/P3-DIMMD1/P3-DIMME1/P3-DIMMF1

CPU4 + 6 DIMMs

CPU4: P4-DIMMC1/P4-DIMMB1/P4-DIMMA1/P4-DIMMD1/P4-DIMME1/P4-DIMMF1

Note:

The drawing above shows DIMM module population for each CPU installed on the

motherboard. Please install your processors starting with CPU Socket 1.

DIMMA1

DIMMD1

DIMME1

DIMMF1

DIMMB1

DIMMC1

Содержание SuperServer SYS-2049U-TR4
























































































































































Результаты поиска

Содержание SuperServer SYS-2049U-TR4

Отзывы:

Похожие инструкции для SuperServer SYS-2049U-TR4

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-2049U-TR4, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-2049U-TR4

Отзывы:

Похожие инструкции для SuperServer SYS-2049U-TR4

Бренды по названию

Популярные бренды