manualshive.com logo in svg

Supermicro SuperServer SYS-110C-FHN4T, Руководство пользователя

Поделиться
Скачать
Supermicro SuperServer SYS-110C-FHN4T Скачать руководство пользователя страница 54

54

Chapter 4: Motherboard Connections

4.3 Input/Output Ports

I/O Ports

See below figure for the locations and descriptions of the various I/O ports on the rear of the 

motherboard.

VGA/DVI-D Port

A VGA port and a DVI-D port are located next to DisplayPorts 1/2 on the I/O back panel. Use 
these connections for VGA and DVI displays. The VGA connector is on top and the DVI-D 
is on the bottom.

DP++ (DisplayPort) 

There are two DisplayPorts located on the rear I/O back panel. DisplayPort, developed by 
the VESA consortium, delivers digital display and fast refresh rate. It can connect to virtually 
any display using a DisplayPort adaptor for devices such as VGA, DVI, or HDMI. 

1

9

8

7

6

5

4

3

2

10

4

13

12

14

11

Rear I/O Ports

#

Description

#

Description

#

Description

1

IPMI LAN

6

LAN2

11

DVI-D

2

USB9 (3.2)

7

LAN1

12

DisplayPort 2

3

USB8 (3.2)

8

LAN4

13

DisplayPort 1

4

USB7 (3.2)

9

LAN3

14

UID Switch

5

USB6 (3.2)

10

VGA

Содержание SuperServer SYS-110C-FHN4T















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды