Supermicro SuperServer 510P-WT Скачать руководство пользователя

Страница: 44 / 113

Chapter 3: Maintenance and Component Installation

DVD-ROM Drive Installation

The SYS-510P-WT/WTR can accommodate a slim DVD drive (optional). Side mounting
brackets are needed to install the DVD drive in the chassis.

Accessing a DVD-ROM Drive

Begin by removing power from the system as described in Section 3.1.

1. Unplug the power and data cables from the drive.

2. Locate the locking tab at the rear of the drive. It will be on the left side of the drive when

viewed from the front of the chassis.

3. Pull the tab away from the drive and push the drive unit out the front of the chassis.

4. Add a new drive by following this procedure in reverse order. You may hear the faint

click of the locking tab when the drive is fully inserted.

5. Reconnect the data and power cables to the drive then replace the chassis cover and

restore power to the system.

Checking the Temperature of an NVMe Drive

There are two ways to check using IPMI.

Checking a Drive

•

IPMI > Server Health > NVMe SSD –

Shows the temperatures of all NVMe drives.

•

IPMI > Server Health > Sensor Reading > NVME_SSD –

Shows the single highest tem-

perature among all the NVMe drives.

Hard Drive Carrier Indicators

Each hard drive carrier has two LED indicators: an activity indicator and a status indicator. In

RAID configurations, the status indicator lights to indicate the status of the drive. In non-RAID
configurations, the status indicator remains off. See the table below for details.

LED Color State

Status

Activity LED

Blue

Solid On

SAS drive installed

Blue

Blinking

I/O activity

Status LED

Red

Solid On

Failed drive for SAS/SATA with RSTe support

Red

Blinking at 1Hz

Rebuild drive for SAS/SATA with RSTe support

Red

Blinking with two blinks and
one stop at 1Hz

Hot spare for SAS/SATA with RSTe support

Red

On for five seconds, then off

Power on for SAS/SATA with RSTe support

Red

Blinking at 4Hz

Identify drive for SAS/SATA with RSTe support

Содержание SuperServer 510P-WT


















































































































Результаты поиска

Содержание SuperServer 510P-WT

Отзывы:

Похожие инструкции для SuperServer 510P-WT

Бренды по названию

Популярные бренды

Supermicro SuperServer 510P-WT, Руководство пользователя

Результаты поиска

Содержание SuperServer 510P-WT

Отзывы:

Похожие инструкции для SuperServer 510P-WT

Бренды по названию

Популярные бренды