manualshive.com logo in svg

Supermicro MicroBlade MBI-6119G-T7LX, Руководство пользователя

Поделиться
Скачать
Supermicro MicroBlade MBI-6119G-T7LX Скачать руководство пользователя страница 43

MBI-6219G-T7LX /MBI-6119G-T7LX MicroBlade Module User’s Manual

4-6

Figure 4-5. Intel B2SS2-MTF Block Diagram

Jumpers

Any jumpers present on the mainboard are used by the manufacturer only; there are no 
jumpers used to configure the operation of the mainboard.

CMOS Clear

JBT1 is used to clear CMOS and will also clear any passwords. JBT1 consists of two 
contact pads located near the BIOS chip.

Clearing CMOS

1. First power down the blade and remove it from the enclosure.

2. Short the CMOS pads with a metal object such as a small screwdriver.

3. Install the blade back into the enclosure and power it on.

C236

PCH

DDR4 (CHA)

IMVP8

SVID

DDR4 (CHB)

DIMM1

DIMM2

MISC VRs

2133/1866/1600MHz

x4 DMI II

8.0GT

2133/1866/1600MHz

FLASH SPI

128Mb

SPI

x4 DMI II

8.0GT

SPI

FLASH SPI

128Mb

PCIe 3.0 X 4

X710-BM2

ASPEED

ASP2400

PCIe 1.0 X 1

PCIe 1.0 X 1

(LAN Switch)

REALTEK

RTL8367MB

USB 2.0 X 2

USB 2.0 X 2

AOM-BPN-MS28HS

SATA 3.0 X 2

SATA 3.0 X 2

6.0Gb/s

6.0Gb/s

480Mb/s

480Mb/s

NODE 1

NODE 2

B2SS2-MTF

INTEL BGA1440

IMVP8

SVID

MISC VRs

RGMII

RGMII

TPM Header

LPC

LPC

GOLD FINGER

10G KRx2

1G Serdes

INTEL BGA1440
Skylake-H
4+4e

PCIe 3.0 X 4

M.2

M.2

PCIe 3.0 X 4

PCIe 3.0 X 4

X710-BM2

10G KRx2

M.2

M.2

PCIe 3.0 X 4

PCIe 3.0 X 4

12V

2 X SATA DOM

2 X 2.5" SATA

(KVM Connector)

AOM-KVM-B2SS2-MTF

RGB, DEBUG

RGB, DEBUG

C236

PCH

ASPEED

ASP2400

TPM Header

DIMM1

DIMM2

DDR4 (CHA)

DDR4 (CHB)

2133/1866/1600MHz

2133/1866/1600MHz

Содержание MicroBlade MBI-6119G-T7LX













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды