Supermicro 6048R-E1CR24L Скачать руководство пользователя | Manualshive

Страница: 50 / 142

background image

5-2

S

UPER

S

TORAGE

S

YSTEM 6048R-E1CR24L User's Manual

5-2 Connecting Cables

Several cables need to be connected to the serverboard. These include the data
cables for the peripherals and control panel and the power cables.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully

routed to prevent them from blocking the flow of cooling air that moves through

the system from front to back. If you need to disconnect any of these cables, you
should take care to keep them routed as they were originally after reconnecting
them (make sure the red wires connect to the pin 1 locations). See the layout on
page 5-10 for connector locations.

Connecting Power Cables

The X10DRH-iT has a 24-pin primary power supply connector (J24) for connection
to the ATX power supply. In addition, there are two 8-pin 12V processor power con-
nectors (JPWR1 and JPWR2) that must be connected to your power supply. See

Section 5-9 for power connector pin definitions.

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the various front control panel buttons and LED indicators.
All JF1 wires have been bundled into a single cable to simplify this connection. Make
sure the red wire plugs into pin 1 as marked on the board. The other end connects
to the Control Panel PCB board, located just behind the system status LEDs on
the chassis. See Chapter 5 for details and pin descriptions.

«
...
48
49
50
51
52
...
»

Содержание 6048R-E1CR24L















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6048R-E1CR24L

Бренд: IBM Страницы: 2

Бренд: Husky Страницы: 8

Бренд: Hamlet Страницы: 10

Бренд: Sans Digital Страницы: 2

HazMat station EPO-2

Бренд: Denios Страницы: 6

Бренд: Zhejiang Longyard Trade Industrial Страницы: 18

Бренд: IBM Страницы: 82

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Бренд: LaCie Страницы: 67

Бренд: Quictent Страницы: 24

Бренд: VME Страницы: 2

STORAGE CAB4000 -

Бренд: Tandberg Data Страницы: 13

Combo ION GHE135C

Бренд: IOGear Страницы: 39

EonStor GS 3000 Series

Бренд: Infortrend Страницы: 134

Бренд: Western Digital Страницы: 2

Бренд: Western Digital Страницы: 2

220-420LTO - QUICK

Бренд: TANDBERG Страницы: 8

StorageWorks E Series

Бренд: HP Страницы: 8

StorageWorks 9000s NAS

Бренд: HP Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды