Supermicro 6048R-E1CR24L Скачать руководство пользователя | Manualshive

Страница: 25 / 142

background image

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel as well as others on the hard drive
carriers to keep you constantly informed of the overall status of the system as well

as the activity and health of specific components. There are also two buttons on

the chassis control panel.

3-2 Control Panel Buttons

The two push-buttons located on the front of the chassis are (in order from left to
right) a reset button and a power on/off button.

Reset

Use the reset button to reboot the system.

Power

This is the main power button, which is used to apply or turn off the main system
power. Turning off system power with this button removes the main power but keeps
standby power supplied to the system. Therefore, the system power cord should
be unplugged before performing service.

3-3 Control Panel LEDs

The control panel located on the front of the chassis has several LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective
action you may need to take.

«
...
23
24
25
26
27
...
»

Содержание 6048R-E1CR24L















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6048R-E1CR24L

Бренд: Far Tools Страницы: 11

Бренд: Apricorn Страницы: 4

Бренд: Sans Digital Страницы: 2

Бренд: Quantum Страницы: 312

HyperDrive COLORSPACE

Бренд: SANHO Страницы: 31

Бренд: Buffalo Страницы: 2

Бренд: Addonics Technologies Страницы: 2

VERTEX 2 SATA II 3.5

Бренд: OCZ Страницы: 3

LITTLE DISK USB 2.0

Бренд: LaCie Страницы: 23

Бренд: Honeywell Страницы: 28

Maxtor Central Axis

Бренд: Maxtor Страницы: 2

Бренд: Toshiba Страницы: 1

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 1

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 1

Бренд: Toshiba Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды