P/N 506020-38
Rev. NC 03/2014
HEARTH PRODUCTS
SUPPLEMENTAL INSTRUCTIONS
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
GLASS DOOR ASSEMBLY REMOVAL
SIGNATURE
™
SERIES GAS FIREPLACES
Figure 1
(2) Latch
Screws
Glass Door
Assembly
Firebox Floor
(2) Door
Latches
~
~
Front View model shown.
Instructions also apply
to See-Through models.
Top Flange
CAUTION
RISK OF PERSONAL INJURY
OR PROPERTY DAMAGE.
• Do NOT abuse glass doors by striking or slamming shut
• Never operate fireplace with glass door assemblies removed.
These direct-vent appliances are designed to operate only when glass
door assemblies are installed. Generally, the glass door assemblies
should not be removed, except when access to components within
the firebox is required.
• Securely tighten door latch screws when reinstalling glass door
assemblies to prevent doors from falling out.
• Handle glass door assemblies with extreme care. Replace dam-
aged glass door assemblies with approved replacement assem-
blies only.
The door assemblies on this fireplace contain ceramic glass. Handle
with care to prevent damage. If the door frame or glass on either
assembly becomes damaged, replace the entire glass door assembly
with a manufacturer-approved replacement assembly only. Do not
attempt to substitute any materials used on door assemblies or
replace cracked or broken glass with any other materials.
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
• Install only when fireplace is OFF and COLD.
• Fireplace surfaces get EXTREMELY HOT!
• The glass on the front of the fireplace reaches EXTREMELY HIGH
temperatures and can cause severe burns if touched. Even after
the gas is turned off, fireplace surfaces remain extremely hot.
• Keep children away from an operating fireplace. Closely supervise
children in any room where a fireplace is operating to prevent
contact with glass.
REQUIRED TOOLS
• #3 Phillips screwdriver
REMOVING GLASS DOOR, MESH PULL SCREENS,
AND MODESTY PANEL
1) Remove the mesh pull screens, as follows:
a) Lift up the left end of the rod to disengage it from the slot in the left
rod bracket.
b) Slowly remove the right end of the rod from the hole in the right
rod bracket.
c) Set aside the rod and mesh pull screens for later reinstallation.
2) Remove the modesty panel from the top flange of the glass door by
firmly pulling up on it with both hands until it is disengaged.
3) Remove glass door, as follows:
a) See Figure 1. While holding the top of the glass door frame in
place, use a #3 Phillips screwdriver to remove the two (2) screws
securing the door frame to the two (2) door latches.
b) Carefully tilt the top of the glass door frame away from the unit (as
shown in Figure 1), and then lift the door assembly up and out of
the lower track.
c) Carefully place the glass door assembly on a padded surface in a
safe location to prevent damage.
See other side for installation instructions.
Note: These instructions do NOT apply to the outer glass door
provided in the Outdoor Kit for indoor/outdoor installations of
Montebello See-Through models.
REMOVAL (AND REINSTALLATION) INSTRUCTIONS FOR GLASS DOOR ASSEMBLIES
FOR USE WITH DRT AND DRC SERIES DIRECT-VENT GAS FIREPLACES
(FRONT VIEW AND SEE-THROUGH MODELS*)
P506020-38
*Model Numbers; DRC6340TEN, DRC6340TEP, DRC6340TYN,
DRT6340TEN, DRT6340TEP and DRT6340TYN, DRC6345TEN,
DRC6345TEP, DRC6345TYN, DRT6345TEN, DRT6345TEP and DRT-
6345TYN, See-Through Models: DRT63STTEN, DRT63STTEP and
DRT63STTYN
f i r e - p a r t s . c o m
