Superior BGE18NV Скачать руководство пользователя страница 1

Страница: 1 / 48

Installation and Operation Instructions

Superior™ Unvented (Vent-Free) Gas Log Heater

P/N 126827-01 Rev. A 01/2014

Models

BGE18NV

BGE18PV

BGE2436NV

BGE2436PV

P126827-01

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not

prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases.

WARNING: This appliance is for installation only in a solid-fuel burning masonry or UL127 factory-built

fireplace or in a listed ventless firebox enclosure. It is design-certified for these installations in accordance

with ANSI Z21.11.2. Exception: DO NOT install this appliance in a factory-built fireplace that includes

instructions stating it has not been tested or should not be used with unvented gas logs.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions

for adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation

section on page 6 of this manual.

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

—

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

—

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

—

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Содержание BGE18NV

















































Результаты поиска

Содержание BGE18NV

Отзывы:

Похожие инструкции для BGE18NV

Бренды по названию

Популярные бренды

Superior BGE18NV, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BGE18NV

Отзывы:

Похожие инструкции для BGE18NV

Бренды по названию

Популярные бренды