SuperFlow SF- 902S Скачать руководство пользователя страница 70

Страница: 70 / 79

7.0 Troubleshooting

This section outlines basic procedures to follow if the component or instruments do not function properly.

Contact SuperFlow Technical Support if you have any questions about the safe operation of the equipment

or for service and advice.

• Post safety warnings and barricade work

area to prevent unauthorized use of the

dynamometer before maintenance has been

completed.

•

Only qualified machine operators and

maintenance personnel should perform the

procedures covered in this manual.

WARNING

7.1 Servo Valve

The following procedure can be used to diagnose whether the servo valves can be controlled by the control

system. These tests function without any closed loop feedback from the electronics. Thus, PID control

parameters are not in play.

Manual test mode:

1. Load the

Diag_Pmk.tgp

test group into your system. If you do not have this test group, contact

SuperFlow Customer Service for a copy.
a.

This contains a config file (.cfa) that changes the inlet valve control mode to always copy the outlet

valve.

b. Thus, it will allow you to control both inlet and outlet control valves in manual mode control without

the engine running. Normally, the inlet valve will not move until engine RPM exceeds 500.

c. If you don’t have the

Diag_Pmk.tgp

, but you have the WinDyn Config editor enabled on your

system, you may edit the

SetIn

channel (103) as follows to enable the inlet valve to copy the outlet

valve:

return(system(1,1,0,0)/40.96);

If you do edit your config file, don’t forget to return the channel to the original setting when you are

finished diagnosing your servo valves. Write down that setting before you edit the file in step C

above.

2. Observe WinDyn screen objects showing the servo in and servo out percentage (objects are typically

on screen 2 or 6; if not add the objects by editing your screen)

Figure 7.1 Servo IN and OUT Percentage

AUTOMATIC STARTING HAZARD.

The dynamometer could be started

remotely. Ensure starting has been

disabled prior to servicing.

WARNING

Содержание SF- 902S
















































































Результаты поиска

Содержание SF- 902S

Отзывы:

Похожие инструкции для SF- 902S

Бренды по названию

Популярные бренды

SuperFlow SF- 902S, Оригинальное руководство пользователя

Результаты поиска

Содержание SF- 902S

Отзывы:

Похожие инструкции для SF- 902S

Бренды по названию

Популярные бренды