Superabrasive User Manual Original Language Lavina
® 20EU
6/2020
14
4.5 CONTROL BOARD
1. ALARM glowing button.
Usually glows when
you pressed the EMG button.
2. USB charger.
3. STOP button
which stops the motor
.
4
.
EMERGENCY button
used to stop the motor in
case of emergency.
5. POWER glowing button
- it glows when the
machine is connected to the electricity.
6. Forward/Reverse switch
.
Select forward for
clockwise rotation of the grinding plates or reverse
for counterclockwise rotation of the grinding plates
(recommended configuration). The preferred
operating direction should be when the switch is in
the forward position. The proper direction of rotation
of the motor (counterclockwise) is indicated by an
arrow on its cover.
7.
Water pump switch.
Glows
in orange when the
water pump is working.
8.
LED lights switch
9. QR code.
When you scan it with your phone for example, it will redirect your browser to Lavina manuals page.
10. READY ON / OFF switch.
If you want to start the motor it must be ON as it puts the inventor into standby mode (it
glows
when it’s turned ON). If it’s off the inventor will be out of standby mode and you cannot start the motor. The switch
returns to its starting position after being released.
11. Cup holder.
12. Potentiometer
.
Controls the RPM of the grinding plates in a range of 300-1100 rpm.
13.
RUN button.
Start the motor (ready ON/OFF switch must be ON).
14. Digital Tachometer.
Indicates the revolution per minute of the grinding plates (not the revolution per minute of the
entire unit).
15. Reset button.
Resets the alarm of the inverter.
16. Phone holder.
4.6 STARTING THE MACHINE
First, follow the directions in the chapter on Safety Devices and Safety Instructions. Next, release the
emergency stop (4),
turn
the
Ready switch (10)
to the ON position to put the machine in standby mode. Check the
potentiometer (12)
, and ensure that
it is set to the working speed. If you are working wet, add water to the floor surface by starting the
pump (7)
. If you are working
dry make sure your machine is connected to the vacuum unit. Finally, hold the machine firmly and push the
RUN button (13)
.
4.7 OPERATING THE MACHINE
Guide the machine in straight lines across the floor, slightly overlapping the previously completed surface with
each new line. Work at a constant speed, allowing the tools time to work at a speed appropriate for the tools’ grit
size. Avoid vibrations. Do not stop the machine while tools are still running as they will mark the surface of the
floor. When working wet, select the destination of the water feed with the water tap (fig. 4.2) and periodically run
the pump to release water onto the floor surface. Starting the pump is possible only if the machine motor is on.
When working dry, check the floor surface periodically for dust accumulation. Check regularly to see if you’re
vacuum works properly.
4.8 STOPPING THE MACHINE
The stopping of the machine must be done gradually until the motor stops. Do not stop moving the machine before the motor
comes to rest, as the tools could damage the surface.
To stop the machine:
1.Push the STOP button (3) .
2.Turn the
ON/OFF
(10) switch
in position
OFF, this will cut the voltage to the invertor and the green light will turn off.
Fgure 4.4
Figure 4.9
Содержание Lavina Elite L20EU
