Super Circuits CD50WD, Руководство пользователя

Страница: 1 / 4

Platinum SerieS
Camera manual
CD50WD Dome Camera
Dimensions : mm
COLOR VANDAL PROOF CAMERA
غ
CONNECTIONS
D144-CB80L-3-TDN3-AC5-CUIV
CD50WD
About this manaul
INSTRUCTION MANUAL
Before installing and using the camera,
please read this manual carefully.
Be sure to keep it handy for later
reference.
TROUBLESHOOTING
SPECIFICATION
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your
service center.
غ
If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
غ
If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt of fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CONNECTOR AND CAMERA SETTING
غ
Do not open or modify
Do not open the cabinet exet during maintenance and
installation, as it may be dangerous and cause damages.
غ
Do not put objects inside the unit
Make sure that no metal objects or flammable substances get
insdie the camera. It could cause fire, short-circuits or damages.
غ
Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
غ
Install away from electric or magnetic fields
غ
Protect from humidity and dust
غ
Protech from high temperature
Be careful when installing colose to the ceiling , in a kitchen or
boiler room, as the temperature may raise to high levels.
غ
Cleaning
Dirt can be removed from the cabinet only by wiping it
with a soft cloth moistened with a soft detergent solution.
غ
Mounting Surface
The mounting surface material must be strong enough to secure
the camera.
͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑
INSTALLATION
CONNECTIONS AND CAMERA SETTINGS
PRECAUTIONS
1 Use the L-Wrench to remove the screw (B).
2 Assemble Case (C) and (D).
3 Align the Case (C) and (D) with the surface of the ceiling;
make marks on the ceiling in the places where the
screw holes are to be drilled, and then drill the four
holes.
4 Cut a hole (diameter: 2.9 in. / 73mm) in the ceiling for
routing the cables.
5 Pass the power cable (E) and video cable (F) from the
camera unit through the cable hole in the ceiling.
6 Align the four screw holes in the camera unit (D) with
the screw holes in the ceiling, and then secure
the camera in place by tightening the four or
more screws (C).
7 Carry out the settings and adjustments for the camera.
8 Secure the dome cover (A) by tightening the screws (B).
Ͳ
ͳ
͵
ʹ
Ͷ
ͷ
͸
CAUTION :
Check for polarity when using a DC 12V power supply.
͵ʹͣ͢·͑͑͠Ͳʹͣͥ·
͵ʹͣ͢·͑͑͠Ͳʹͣͥ·
GENERAL Spec NTSC PAL
CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed
1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
ME/AE
ATW/AWB
WDR ON/OFF
AGC MAX ON
Electrical Spec
Operating Voltage
Power Consumption
Mechanical Spec
Operation Temp
Air Humidity
Lens Mount
Connections via
BNC(VIDEO), 2P WIRE(Power)
0.45
0.06fC, 0.6Lux(Scene) With F1.2 Lens
480TV Lines
10Vp-p/75ohm Composite
Internal (12VDC) / External (Line Lock, 24VAC)
> 45dB [AGC off]
12VDC -3.9W, 24VAC - 4.0W
12VDC(11-20V), 24VAC(20-27V)
3.3-12mm
DIP Switch Select ATW/AWB (ON/OFF)
DIP Switch Select ME/AE (ON/OFF)
Up to max.90%
14°F ~ 131°F ( -10
π
C ~ +55°C )
DIP Switch Select ON/OFF
DIP Switch Select WDR (ON/OFF)
Dimensions : mm
COLOR VANDAL PROOF CAMERA
غ
CONNECTIONS
D144-CB80L-3-TDN3-AC5-CUIV
CD50WD
About this manaul
INSTRUCTION MANUAL
Before installing and using the camera,
please read this manual carefully.
Be sure to keep it handy for later
reference.
TROUBLESHOOTING
SPECIFICATION
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your
service center.
غ
If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
غ
If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt of fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CONNECTOR AND CAMERA SETTING
غ
Do not open or modify
Do not open the cabinet exet during maintenance and
installation, as it may be dangerous and cause damages.
غ
Do not put objects inside the unit
Make sure that no metal objects or flammable substances get
insdie the camera. It could cause fire, short-circuits or damages.
غ
Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
غ
Install away from electric or magnetic fields
غ
Protect from humidity and dust
غ
Protech from high temperature
Be careful when installing colose to the ceiling , in a kitchen or
boiler room, as the temperature may raise to high levels.
غ
Cleaning
Dirt can be removed from the cabinet only by wiping it
with a soft cloth moistened with a soft detergent solution.
غ
Mounting Surface
The mounting surface material must be strong enough to secure
the camera.
͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑
INSTALLATION
CONNECTIONS AND CAMERA SETTINGS
PRECAUTIONS
1 Use the L-Wrench to remove the screw (B).
2 Assemble Case (C) and (D).
3 Align the Case (C) and (D) with the surface of the ceiling;
make marks on the ceiling in the places where the
screw holes are to be drilled, and then drill the four
holes.
4 Cut a hole (diameter: 2.9 in. / 73mm) in the ceiling for
routing the cables.
5 Pass the power cable (E) and video cable (F) from the
camera unit through the cable hole in the ceiling.
6 Align the four screw holes in the camera unit (D) with
the screw holes in the ceiling, and then secure
the camera in place by tightening the four or
more screws (C).
7 Carry out the settings and adjustments for the camera.
8 Secure the dome cover (A) by tightening the screws (B).
Ͳ
ͳ
͵
ʹ
Ͷ
ͷ
͸
CAUTION :
Check for polarity when using a DC 12V power supply.
͵ʹͣ͢·͑͑͠Ͳʹͣͥ·
͵ʹͣ͢·͑͑͠Ͳʹͣͥ·
GENERAL Spec NTSC PAL
CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed
1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
ME/AE
ATW/AWB
WDR ON/OFF
AGC MAX ON
Electrical Spec
Operating Voltage
Power Consumption
Mechanical Spec
Operation Temp
Air Humidity
Lens Mount
Connections via
BNC(VIDEO), 2P WIRE(Power)
0.45
0.06fC, 0.6Lux(Scene) With F1.2 Lens
480TV Lines
10Vp-p/75ohm Composite
Internal (12VDC) / External (Line Lock, 24VAC)
> 45dB [AGC off]
12VDC -3.9W, 24VAC - 4.0W
12VDC(11-20V), 24VAC(20-27V)
3.3-12mm
DIP Switch Select ATW/AWB (ON/OFF)
DIP Switch Select ME/AE (ON/OFF)
Up to max.90%
14°F ~ 131°F ( -10
π
C ~ +55°C )
DIP Switch Select ON/OFF
DIP Switch Select WDR (ON/OFF)
Dimensions : mm
COLOR VANDAL PROOF CAMERA
غ
CONNECTIONS
D144-CB80L-3-TDN3-AC5-CUIV
CD50WD
About this manaul
INSTRUCTION MANUAL
Before installing and using the camera,
please read this manual carefully.
Be sure to keep it handy for later
reference.
TROUBLESHOOTING
SPECIFICATION
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your
service center.
غ
If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
غ
If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt of fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CONNECTOR AND CAMERA SETTING
غ
Do not open or modify
Do not open the cabinet exet during maintenance and
installation, as it may be dangerous and cause damages.
غ
Do not put objects inside the unit
Make sure that no metal objects or flammable substances get
insdie the camera. It could cause fire, short-circuits or damages.
غ
Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
غ
Install away from electric or magnetic fields
غ
Protect from humidity and dust
غ
Protech from high temperature
Be careful when installing colose to the ceiling , in a kitchen or
boiler room, as the temperature may raise to high levels.
غ
Cleaning
Dirt can be removed from the cabinet only by wiping it
with a soft cloth moistened with a soft detergent solution.
غ
Mounting Surface
The mounting surface material must be strong enough to secure
the camera.
͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑͑
INSTALLATION
CONNECTIONS AND CAMERA SETTINGS
PRECAUTIONS
1 Use the L-Wrench to remove the screw (B).
2 Assemble Case (C) and (D).
3 Align the Case (C) and (D) with the surface of the ceiling;
make marks on the ceiling in the places where the
screw holes are to be drilled, and then drill the four
holes.
4 Cut a hole (diameter: 2.9 in. / 73mm) in the ceiling for
routing the cables.
5 Pass the power cable (E) and video cable (F) from the
camera unit through the cable hole in the ceiling.
6 Align the four screw holes in the camera unit (D) with
the screw holes in the ceiling, and then secure
the camera in place by tightening the four or
more screws (C).
7 Carry out the settings and adjustments for the camera.
8 Secure the dome cover (A) by tightening the screws (B).
Ͳ
ͳ
͵
ʹ
Ͷ
ͷ
͸
CAUTION :
Check for polarity when using a DC 12V power supply.
͵ʹͣ͢·͑͑͠Ͳʹͣͥ·
͵ʹͣ͢·͑͑͠Ͳʹͣͥ·
GENERAL Spec NTSC PAL
CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed
1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
ME/AE
ATW/AWB
WDR ON/OFF
AGC MAX ON
Electrical Spec
Operating Voltage
Power Consumption
Mechanical Spec
Operation Temp
Air Humidity
Lens Mount
Connections via
BNC(VIDEO), 2P WIRE(Power)
0.45
0.06fC, 0.6Lux(Scene) With F1.2 Lens
480TV Lines
10Vp-p/75ohm Composite
Internal (12VDC) / External (Line Lock, 24VAC)
> 45dB [AGC off]
12VDC -3.9W, 24VAC - 4.0W
12VDC(11-20V), 24VAC(20-27V)
3.3-12mm
DIP Switch Select ATW/AWB (ON/OFF)
DIP Switch Select ME/AE (ON/OFF)
Up to max.90%
14°F ~ 131°F ( -10
π
C ~ +55°C )
DIP Switch Select ON/OFF
DIP Switch Select WDR (ON/OFF)