SUNWARD SWE50B Скачать руководство пользователя страница 68

Страница: 68 / 197

Make sure using slope or loading platform

to load or unload.

4.3 TRANSPORT ON HIGHWAY

Before transportation on highway (As figure 4.1.2), you should know

and follow all the related regulations.

Check the length, width, height, and weight of the trailer that

loads excavator.

Check transportation route conditions, such as dimension and

weight limitations and traffic rules.

Sometimes, it is necessary to separate excavator to

smaller parts to satisfy the limitations of dimension or

weight.

Transport excavator with trailer

Please choose proper trailer to transport the whole

excavator (As figure 4.1.3).

Please consult with your dealer for the trailer choice.

The trailer should be placed on hard horizontal ground to

load and unload excavator.

Slope or loading platform

(1)

Before loading or unloading, clean the slope or loading platform and the carriage bed. The slope,

loading platform, and carriage bed with smear, earth, or ice have the danger of slippage.

(2)

Place chocks under the trailer head or wheels when use slope or loading platform to load or

unload.

(3)

The slope should have enough width, length, and intensity. The obliquity of slope should be less

than 15



without fail.

(4)

Loading platform must have plenty of width and intensity to support excavator, and the gradient

must be less than 15



Figure 4.1.2

Figure 4.1.3

Содержание SWE50B






































































































































































































Результаты поиска

Содержание SWE50B

Отзывы:

Бренды по названию

Популярные бренды

SUNWARD SWE50B, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SWE50B

Отзывы:

Бренды по названию

Популярные бренды