SUNWARD SWE50B Скачать руководство пользователя

Страница: 54 / 197

Attention:



It must follow all safety regulations when the machine lifts objects.



Don't use damaged chain, wire rope, or cord in lifting work, or GBH may occur (As figure 3.7.2).



Don't move the load suddenly. Don't move load on the top of human beings. Don't permit

everybody adjacent to the load.



Ensure everybody away from lifted or tight wire-tied and on the ground load, until the chocks

support the load or the load has been stably placed on the ground.



Fix upper structure, and make the traveling motor on the rear.



Don't connect sling/chain on the bucket teeth.

(1)

Sling/chain should tightly bind the load down, the workman should glove when bind sling/chain.

(2)

Connect sling/chain with bucket lifting ring, curled bucket, and retracted arm.

(3)

Before starting, it should uniform the hand signal with signalman.

(4)

Acquaint with the positions of all workmen in the range of working area.

(5)

Connect hand rigging on the load and ensure the people pulling hand rigging away from load.

(6)

Try to lift the load before normal operation.



Park the machine beside the load.



Connect the load on the machine.



Lift load to 50mm (2in) height to the ground.



Swing the load to one side.



Keeping load close with ground, move the load

from the side of machine.

(7)

Just lift the load to required height.

3.8 HYDRAULIC BREAKING HAMMER

Tips for operating hydraulic breaking hammer -if equipped

Choose breaking hammer of correct dimension and weight

for excavator. Consult with your dealer.

Attentions for hydraulic breaking hammer tubing

(1)

When the hydraulic breaking hammer is out of

use, cover the pipe end of arm end and dismantle

Wrong

错误

Wrong

Содержание SWE50B






































































































































































































Результаты поиска

Содержание SWE50B

Отзывы:

Похожие инструкции для SWE50B

Бренды по названию

Популярные бренды

SUNWARD SWE50B, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SWE50B

Отзывы:

Похожие инструкции для SWE50B

Бренды по названию

Популярные бренды