SUNWARD SWE50B Скачать руководство пользователя страница 53

Страница: 53 / 197

work, place dozer blade at rear to guarantee

safety.

Prevention measurement for dozer blade

(1)

Don’t use dozer blade to dig, otherwise it will damage dozer blade or crawler system.

(2)

Dozer blade can’t support large or unstable barycenter objects, otherwise it will
damage dozer blade or crawler system.

(3)

When the machine traveling, dozer blade can’t draw any object, otherwise it will
damage dozer blade or crawler system.

(4)

When prop up machine with dozer blade, the ground should be plane to ensure dozer

blade touching ground stably.

Be careful when retract foreside work device

Don’t allow the bucket to collide with dozer blade.

Don’t allow dozer blade to touch roadblock

Don’t allow dozer blade to touch roadblock, otherwise dozer
blade, cylinder, or other components will be damaged.

3.7 LIFTING WORK

Lifting hook mark (As figure 3.7.1)

Figure 3.7.2

Содержание SWE50B






































































































































































































Результаты поиска

Содержание SWE50B

Отзывы:

Бренды по названию

Популярные бренды

SUNWARD SWE50B, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SWE50B

Отзывы:

Бренды по названию

Популярные бренды